UPVC Window Handle Replacement

Replacing a broken window handle is a relatively easy task and with the right tools it can be done quite quickly. However, it is essential to know your type of handle and the spindle's length prior to purchasing an alternative.

Older uPVC windows use handles with cockspurs, which have an extension spur that can lock over a cockspur wedge striker plate. They can be left- or right-handed, and must be compatible when replaced.

What kind of lock or handle do you have? I have

There are a variety of window locks and handles made from upvc, each with its particular advantages and uses. The type of handle you have will determine how easy it is to open your windows and if the locking mechanism functions in the way you want it to. With time and regular use the handles made of upvc on your windows could be damaged and worn out. This makes them less secure and less effective. In certain instances, they might even fall completely off. If you notice that your upvc window handles have fallen off, it's important to fix them as soon as you can. This will stop possible burglaries, and keep your house secure.

It's a task that virtually anyone can perform. With just a few tools and the right information it's a simple procedure that should take no longer than a couple of minutes. You must be aware of the type of lock or handle you have on your window. This will help you select the right replacement.

Inline Espagnolette Handles

They are typically located on the sides of the window. They have a flat design and feature a latch that connects to the locking mechanism on the window frame when turned. Inline upvc handles feature an elongated spindle that runs through middle of the handle to the window frame to control the latch.

Cockspur Handles

These handles are usually found on older uPVC window frames. They have distinct hook-shaped designs. Cockspur handles are held to the frame of the window with a single screw and are less secure than other types of window handle.

Handles that can tilt and turn

The tilt and turn handles are different from other upvc handles in that they can be turned for opening the window, and then tilted into the window to allow air circulation. They have a 7mm spindle in the back and are available in left and UPVC Window Handle Replacement right-handed versions.

When you are purchasing replacement handles for upvc It is crucial to verify the length of the spindle since not all of them are identical in size. To test the length of your handle made of upvc, simply drop something into the middle of the hole, and then measure how far down it goes before it reaches an obstruction. This is the maximum size of spindle that will fit in your windows.

What is spindles?

uPVC window handles work similarly like doors, turning the handle to open a latch inside the frame. This opens the window so that it can be closed and opened. These handles can be damaged, particularly if they're used frequently or subjected to harsh conditions. You may have to replace the handles on your uPVC window if they are not functioning correctly.

There are a variety of uPVC handles that are available, including Espag, Upvc Window Handle Replacement Cockspur and Spaded handle options. They are made in a variety of ways to fit into uPVC frames. Each handle type uses an individual spindle to lock the window mechanism. It is important to identify the type of handle installed on your uPVC windows to ensure that you replace it with a suitable one.

The base section of the handle will tell you what type of uPVC it is. There should be a "snap in cover' over one screw that holds the handle's base in place. Remove this and then you should be able to see the second holding screw on the opposite side of the base of the handle. After both screws are removed then you should be able to pull the handle from the uPVC.

After taking off the uPVC handle, carefully unscrew it from the locking mechanism. Take note of the length of the spindle. You'll need purchase a new one that is the same length as the handle that was originally used and the locking device.

The spindle wears down and is unable to operate the locking mechanism. This could be due to corrosion, damage from constant use or the locking mechanism becoming looser. When this happens it is required to replace the window handle and the locking mechanism to restore full functionality to your uPVC windows.

How do I get rid of the handle from the previous one?

In the course of time and daily use, window handles may become damaged or broken and if this happens, it is essential to fix them as soon as you can to ensure the security of your home. It is good to know that replacing a damaged or worn handle is a fairly simple task that can be accomplished in just over a minute and doesn't require any special tools.

To take off the handle, first remove the screw that is located at the base of the handle. Once the screw has been removed, the handle can be removed. A second screw is located at the bottom of the handle. This can also be removed. Once the two screws are removed, the handle can be detached from the window's base.

After the handle has been removed, take the new handle and line up the fixing holes with the holes that are present in the window frame. There may be a little cap or sticker on the new handle, so take off them if needed and then screw the handle into its place. Once the handle is set, it is essential to check that it works by turning the handle, and ensuring that the lock mechanism activates.

Espag handles have an elongated spindle that extends from the handle and slots into a multipoint locking mechanism within the frame of the window. Cadenza windows come with a blade with cut-outs that slot into the lock mechanism while Cockspur handles have a long nose that is able to hook over either the frame's outer or the transom bar cross member in the glass window replacement.

Once you have installed the new handle, slide the spindle inside the window lock and tighten it. Replace the snap-in cover and screw cap (if necessary) once the handle has been firmly fixed. The handle is now ready for use, so try opening and closing the window a few times to make sure that it works properly and securely.

How do I install the new handle?

It's not difficult to alter the handle on your Upvc windows. The process is very simple. You only need a screwdriver and a little bit of patience. The first thing to do is ensure that the handle is not locked and then take out any screws that are visible, you can replace them with screw caps if needed. Once the handle is removed and you are ready to take an outline of the length of the spindle that extends from the back of the handle. This is important as it will determine what kind of handle you will need to buy.

Espagnolette handles made of uPVC are the most popular type of handle. They have a spindle which runs through the handle and acts as an internal locking mechanism within the window frame. The handle releases the latch, allowing the window to open. When used regularly and time, espagnolette handles may be damaged.

Cadenza handles are a form of uPVC handle that is commonly employed with tilt and turn windows. They have an extended blade that works an interlocking mechanism that is multipoint within the window. They are usually more secure than espagnolette handles as they are only accessible from the inside. They can be replaced using the same method that you would for espagnolette handles, but make sure the new handle is angled, not flat.

Once you have decided on the right handle to purchase then you can align the new handle with the existing screw holes, and then screw it in the appropriate position. After that, you can put the screw covers on and test the new handle. You can perform this by moving the handle back and forth from the locked position to the unlocked several times. It may be worth contacting an expert to determine whether you can solve any problems. They will often be able to guide you on the best way to solve the issue in a quick and effective way.