Repairs to uPVC Windows

uPVC windows are a great option for modern homes. They are easy to maintain and are durable and long-lasting. As opposed to aluminium and timber they are not susceptible to corrosion or rot.

Cleaning and lubricating regularly UPVC windows and doors is vital. This will reduce costly repairs and improve energy efficiency.

1. Broken Glass

If the glass in your window has been damaged, it can cause a huge amount of damage to your home, which can make it very hazardous and possibly fatal. You should take the time to make sure that your windows are in good condition.

For single pane windows it can be relatively simple to replace them, and the replacement will usually fit inside the old frame very easily. However, if you have double pane windows that are secured by internal beading, it'll be more difficult to take out the panes that are in place and replace them with new ones. In this case it is essential to buy plastic spacers to make sure that the new pane fits into the window frame.

If you're planning to try to remove the window panes by yourself, it is essential to wear appropriate safety gear such as gloves that are thick and eye protection. It is also recommended to lay down a drop cloth before you begin working on the glass, so that any shards will fall onto the cloth instead of onto the floor, where they could be trampled on and cause further damage.

It's a good idea to tape the gap once the glass is removed. This will stop water and drafts from entering your property until a professional is able to repair the window. It also acts as an obstruction to prevent criminals from getting into your home. If the gap is particularly large, you might want to consider using a security door that has an integrated window, as it will provide the best of both worlds.

2. Sagging

uPVC is durable energy-efficient, cost-effective and economical alternative to timber sash windows. Over time, upvc window Repair they can develop a variety of issues, including sliding. A sagging window in upvc window repair can cause problems with light, draughts, and even security. It's crucial to act as soon as you notice your uPVC windows are sagging.

To repair a window that is sagging, you can try repositioning the hinges. To do this, you'll need to open the window so that you can get to the frame. Then, you can remove the hinges on the top and bottom using a screwdriver and adjust them clockwise or counter-clockwise. Close your window to check the fit after having relocated your hinges. If you're happy with the fit, tighten the screws to ensure that they stay in place.

If you cannot reposition the hinges, you might need to replace the seal. Seals made of rubber can dry out and lose their elasticity with time, leading them to loose their elasticity. It is crucial to replace your seal as quickly as you can to ensure that your uPVC window watertight and draughtproof.

uPVC handles could also loosen. Often it is due to screws that have come loose over time. However, it could occur because the handle mechanism has worn out. It's relatively easy to fix a loose uPVC hand. You'll first need to close the window and do an initial fitting. The joint at the corners of the sash should be aligned with the joint on the casing. If it does not you can use a screwdriver to loosen up the handle. Then, turn the mechanism to position.

3. Water Leaks

It is essential to take action if you get up each morning to find mouldy walls and floors that are wet. The leaks of water through windows repair could cause structural damage to your home and also impact your ability to regulate the temperature inside your home. Most of the time, uPVC window leaks are caused by a damaged or missing sealant.

This is a relatively easy fix and should be undertaken by any skilled DIYer. Depending on how serious the issue is, old caulking may need to be removed. When it comes to uPVC repair, it is important to be careful not to over-caulk. This will only make your window more difficult to clean and lower its energy efficiency.

It is important to check that any drainage holes are clear of debris and that the sill pan is placed in a way that allows it to drain away from the window. In more serious situations, you may have to replace the window.

Other signs of long-term water leakage are rotted sills and the appearance of black spots of mold on the wall near the window. The is a fungus that thrives in damp conditions and can quickly spread throughout the home.

If the leakage is occurring between the double-glazed window, it is more likely the issue is more with the seal than the frame. Again this can easily be corrected by an uPVC window specialist who can replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are stiff to open, or slack and open in a breeze It could be hinges that are at fault. They can be easily repaired by any skilled DIYer and can usually be completed in just a few minutes.

Nearly every home in the UK will have either top hung or side-hung uPVC windows that are hinged and like any mechanical part they are susceptible to wear and tear over time. It's very simple to change a window hinge, but it's easier if someone else helps you hold the frame.

Check that the uPVC hinges are open and closed in the proper direction. This can be done by looking for the arrows on each hinge. This shows which way the window should be opened.

Faulty window hinges could be caused by improperly opening the window a certain way or by poor installation at the factory. Sending us a picture via our website will often solve the issue. We are always happy to give assistance.

It is also crucial to ensure that the hinges are lubricated regularly. Applying a light engineering lubricant on the hinges is an ideal method to accomplish this. We recommend using the lubricant that doesn't contain solvents, such as 3-in-1 Multi-Purpose oil. Regular lubrication will make the window easier to open and close. It also decreases the possibility of a window getting stuck and stop corrosion. It is recommended to do this once a year. WD40 and other solvent based fluids are not recommended since they will damage parts of your uPVC window.

5. Draughts

Draughts can be caused by different things. Firstly the hinges, again because of wear and tear, can become misaligned, this causes a gap to form where the sash meets the frame. They can be repaired by giving them good clean, but if they are beyond repair it could be necessary to get them re-aligned or replaced. In addition, the interlock could be misaligned. This happens on the hinge's side, Upvc Window Repair and may need to be cleaned. In some instances it might be necessary to replace the hinges.

The next most common cause of draughts is the window seals. They are susceptible to being worn out or damaged over time and will allow air to escape through these gaps. Replacement of these with high-quality weatherstripping can help stop draughts. Replace the windows made of upvc with low-emissivity glasses. This will help regulate indoor temperatures, and reduce the possibility of draughts.

Another method of reducing draughts effectively is by using a draught-excluder. These are usually fabric tubes filled with a filler, which can be hung over your window sill. They will help stop cold air from entering and keep your home warm and cozy!

With a little regular maintenance and repairs, your upvc windows will continue to provide a great level of insulation and security for your home. However, it is important to recognize that all windows have a lifespan and eventually, they will reach the point when it's more economical to replace them than fix them. So, if you're experiencing problems with your upvc windows, it is always best to seek professional assistance as soon as possible.