Cat flaps allow your pet to go in and out whenever they want without having to let them in or out. They also prevent your cat from peeing in the house.

Installing a cat flap into a door panel made of Upvc is much simpler than installing one in a glass door, but it will require some expertise and the appropriate tools.

Take a look at the Door

Installing a cat flap on the door can be a challenge however, as long as you choose the right type of cat flap, take your time and follow the instructions provided it shouldn't be too much trouble. We will help you draw the shape and then use an jigsaw to cut out the door area. Then, we'll finish the job by attaching the cat flap. This will ensure that the flap is in place and also protects the doors from the damage caused by rain and wind.

To determine the size of the cat flap that you require, take a measurement of your pet's width. This will enable you to select a flap that is big enough to allow your pet to go into the house and exit without having to open the door each time.

If your kit comes with an illustration of where to drill then you can stick it on the door and then draw a pencil around it. If your door has a sill or moulding on the bottom edge of it ensure you have clearance from these to ensure your cat's safety and prevent them gaining access to your home.

Next put on your eye protection and a dust mask. Then using a jigsaw start to cut according to the lines you penciled in, don't try to press the blade too hard as this can cause it to cut more quickly than you want it to. If you own a square that you have cut, make use of it to verify that you're cutting properly and to make sure the hole is a good rectangle shape, once you are satisfied with this you can begin to take off the remaining door material.

Draw a Line

The cat flap is a great method to let your pet in and out without worrying about them being in the house with a visitor, or leaving unwelcome gifts in the house. It also helps prevent draughts and helps keep your home's temperature steady. However, fitting the cat flap in upvc door Panel flap to your door might seem like an overwhelming task for those who haven't done it before, which is why many people to call an expert joiner or carpenter to complete the task. While this is certainly an option, it's possible to complete the task yourself if you have the right tools and follow the instructions carefully.

Although this is much simpler to accomplish with a timber door, it is still possible in uPVC doors, but you should be cautious not to damage the doors since this could end the warranty. First, you must take measurements of the door to ensure it will accommodate the new cat-flap. If you have an ordinary uPVC panel it's easy. However in the case of composite or another type of door, you might need to be more careful.

The next step is to measure the size of your cat's belly. This is the distance from the floor to the bottom of the cat's stomach, and you'll need find a place near the door where this measurement is within the range your cat is able to comfortably walk through. Once you've figured out the measurements, you'll have to mark the area with a spirit level and a pencil, cat Flap in upvc door panel so that you are sure that the hole will be suitable for your cat.

Once you have marked out the area, it's time to cut out the hole. It is crucial to take your time and use a jigsaw in order to ensure the cuts are clean and smooth not rough and uneven. This could damage your door. Wear safety glasses and a dust mask when using a Jigsaw. Inhaling sawdust can be harmful for your health. After you've completed the cutting process, you will have to smooth out the edges of the hole using sandpaper, so that the cat flap will fit easily.

Make a hole

It can be a challenge to install an animal flap on the door panel or double glazing unit. If you are not very skilled in DIY, it's recommended to hire a professional to do the work for you. A botched job may not only look ugly, but it could also be a security risk and also allow cold air to enter when the cat is outside and hot air to escape inside.

Mark the hole position on the door with an eraser and a spirit level. This will ensure it is properly positioned and is flush with the rest of the door. Make sure you have sandpaper on hand to smooth out any rough edges.

After the line is drawn, you can cut the hole with a jigsaw, remember to wear any safety gear for working with an electric tool. If you're concerned about the noise, you can purchase a cordless jigsaw which is more quiet and easy to use.

You should only remove the material needed to make the cat flap. It is essential to leave some extra material to cover the wall of the flap. However cutting off too much material can cause problems or even damage the door frame.

A upvc door may have a metal frame or panel that could interfere with the microchip cat flap if this is the case, you will need to cut an oversize hole to ensure the metal doesn't get in contact with the the cat flap. If this is done, it is important to fill in the gap and make it watertight.

If you are fitting the cat flap onto a upvc door or double glazed window with a metal frame then you'll need to speak to a specialist who can provide you with a new pane of glass that already has the hole for the cat flap installers near me flap in it. This is less expensive than trying to fit a cat flap glass door installation near me flap in an existing pane that was not made specifically for this purpose.

Install the Flap

Cat flaps allow your pet the freedom to come and go whenever they want and let them relax in the house when they'd like. If you have a uPVC front door, it may be difficult to put in the cat flap. This is especially true if you do not own a glass panel that can be cut. Luckily, if you're happy to purchase and install a new half-glazed uPVC panel, then it's possible to install an animal flap onto the doors. It's not as easy as simply cutting a hole through the door though and there are some things you'll need to do first to ensure it's safe.

A composite, uPVC or GRP door panel is usually made up of a plastic skin that is attached to an insulating polystyrene core. It is crucial to be cautious when cutting the material. This kind of door typically includes a template which you can use as a reference for cutting the hole in the door.

After you've marked the position of the hole in your door, now it's time to put in the cat flap installers flap itself. You can buy and fit various models that range from simple push-button operated ones to ones that are activated by microchips that only let in your pet. But, regardless of the type of cat flap you choose it's important to make sure that your cat is able to use the flap without getting stuck outside in the rain.

A circular fitting a cat flap in a upvc door is more effective than a square, because circles can be cut more securely into the glass. This is because square holes make glass more vulnerable to cracking when a drill is used on it. This is also a safer option since you don't have to drill into the toughened glass which could break and cause harm to your pet or your family members. This is particularly crucial if you have a child or elderly person in your home who may be injured by shards of glass.