How to Replace the Replacement Key Battery For the Saab 9-3

Saab owners must follow a set of special steps to install an additional ignition key. It requires dealer support using an electronic handheld computer called Tech-2. Then the transponder is replaced and a key are required to be purchased.

Make sure to rotate your keys in order to prevent one from deteriorating faster than the other. This will keep your keys in top condition.

Replacement Case

The new key fobs are not like the older Saab keys. They are equipped with electronics which make it hard to duplicate. This has made stealing cars significantly more difficult than it was twenty years ago. However, it has made the replacement of lost keys an incredibly expensive endeavor.

Saab 9-3 owners should have two keys working. It is costly to replace a lost key because it requires replacing the CIM module, and programming the locking cylinders. Dealers usually charge between $100-$200 for this.

There are ways to reduce these costly. Some parts dealers will search for the code on an extra key (usually the same one that opens the doors and turns the ignition) and cut a brand new key blade from metal for a fraction of the dealer's cost. The key must be the exact same as the original in order for it to function in your vehicle.

You can also change the case yourself by following these steps. You'll require a flathead screwdriver and some patience. With the screwdriver, slowly break the plastic and remove the emergency key from the case. Once the case is open, remove the electronic components and put them in your new case. Make sure you insert the correct key and badge inside the case.

replacement saab key Battery

The Saab 9-3 replacement battery is a budget component that can be easily and quickly replaced. This video tutorial on DIY from YouTube Cyclone Cyd will show you how to replace the battery for the remote key fob in only four steps. This tutorial should work for any modern saab-type key fob, though the process may vary slightly.

The first step is to find the button that opens the backup key within the fob. It is usually located just below the Saab logo on the back of the fob. Next take a flathead screwdriver to insert into the small hole in this button. This will be enough to allow you to open the case of the fob to allow you to replace the battery.

After the new battery CR1632 is installed it is possible to reassemble the remote key fob and program it to your car. The entire process shouldn't exceed an hour. This is a very easy procedure that doesn't require special tools.

The process is more complicated if you've lost your key, but it's possible. The dealer has to first verify the VIN of the vehicle and then order a replacement TWICE module and key blade with the proper unique code. Then, they'll need to cut the replacement key and then program it using an innovative software tool called MDI.

Key Replacement Fob

The key fob is a device that locks and unlocks your car, it has an internal battery. Batteries have a limited lifespan and eventually die. This is a typical issue that happens to all cars and the good news is that you can replace the batteries in a majority of key fobs without having to replace the whole case. You can buy fobs replacements on Amazon that come with all the electronic components already in place, so you'll just pop open the case and replace the old batteries. It's important to note that you will need to remove the emergency key first, and you can do this by inserting a small flathead screwdriver into the slot found in the middle of the case. Work the screwdriver around the case until it is split open, making it easy to remove.

If you are about to replace the keys, ensure you have spare keys, because this can cut down the total cost by a substantial amount. If you have spare keys, you can ask the dealer cut a new key and program it into your car, which is much cheaper than replacing the entire key fob.

If you do not have a spare key, it is possible to add a second key to your car, but this requires a lot of research and effort. It will cost you a few hundred dollars to purchase a second car key. The computer in the vehicle must also be programmed. This can be done by a professional, but it's a costly choice for most owners.

Replacement Ignition

The modern SAAB 9-3 is a more sophisticated alarm system built on a keycode. If you lose your primary key, it may be costly to get another one since the car needs to have a specific computer installed and be programmed to accept a brand new key. Most locksmiths cannot do this and a dealer will charge several hundred dollars to program the new key!

If you've lost the only working key, a dealer will repair your car's computer (known as the CIM or SAAB TWICE) to make a replacement, and they will charge a premium for it. We can reprogram the current EEPROM inside your car's computer to make it prepared for a new key. This will save you more than 50% of the cost you pay an auto dealer.

If you've owned a SAAB 9-3 for gohammer.co.kr many years and you're aware of the ignition keys are not very durable. If the ignition key you have isn't functioning properly, you must look into replacing it. They can become extremely sticky and the buttons are known to fall off. It's not as difficult as you think to replace the ignition key. With the right tools, it is able to be done quickly.