Repairs to uPVC Windows

uPVC is a great choice for modern homes. They are durable, long-lasting and easy to maintain. They are not susceptible to get rotten or rusty like aluminum and timber.

Regularly cleaning and lubricating UPVC windows and doors is essential. This will reduce repair costs as well as improve the efficiency of energy.

1. Broken Glass

The broken glass in your windows can cause severe damage to your home and even be fatal. It is essential to take the time to make sure that you're doing everything you can to ensure that your windows are in good shape.

For single pane windows, it is relatively easy to replace windows, and the new one is usually able to fit into the old frame very easily. However, if you have double pane windows that are secured by internal beading, it will be more difficult to take out the old panes and put in new ones. In this situation you'll need find some plastic spacers to help the new pane to fit perfectly into the frame of the window doctor.

If you're planning to try to remove the glass panes yourself it is important to wear the appropriate safety equipment, including thick gloves and eye protection. It is also recommended to lay down a drop cloth before you start working on the glass so that any fragments of glass fall onto the cloth instead of landing on the floor where they could be trampled upon and cause further damage.

Once the glass is removed and the glass is removed, it's a good idea to seal the gap with some clear packaging tape or duct tape to block drafts and water from entering the property until a professional can come out and fix the window. It also acts as a barrier, deterring any intruders to gain access into your home. If the gap between the window and the door is substantial, you may prefer security screens that includes windows. This will give you the best of both.

2. Sagging

uPVC windows and doors are an affordable energy-efficient, durable and long-lasting alternative to timber windows with sash. In time, they could develop a number of problems, including sagging. A window that isn't properly aligned can cause problems with light, draughts and even security. If you find that your uPVC window is beginning to lose its shape, it's important to act quickly to stop the issue from getting worse.

To fix a sagging window you can try to reposition the hinges. To do this, you'll need to open the window so that you can get to the frame. Then, using a screwdriver, you can take off the hinges at the top and bottom and adjust them by turning them clockwise or counter-clockwise. Close your window to check the fit after having relocated your hinges. If you're satisfied with the fit, tighten the screws to ensure they stay in place.

If you are unable to reposition the hinges, you could need to replace the seal. Over time rubber seals can lose their elasticity and become dry, which causes their tightness to decrease. It is crucial to replace your seal as quickly as you can to keep your uPVC window watertight and draughtproof.

uPVC handles could also loosen. The majority of the time it is due to screws that have come loose over time. However, it could be due to the fact that the handle mechanism has worn out. It's relatively easy to repair a loose uPVC handle. First, you'll need to shut the window and do an initial fitting. The joint at the corners of the sash must align with the joint on the casing. If it doesn't, you can use a screwdriver or a wrench to loosen the handle and then reverse the mechanism back into its original position.

3. Water Leaks

It is essential to take action if you awake each day to discover mouldy walls and floors that are wet. Windows that leak water do not only lead to the degradation of your home's structure but also hinder your efforts to control the temperature in your home. Most often, uPVC window leaks are caused by damaged or missing sealant.

It is a fairly easy fix that can be completed by any competent DIYer. Depending on the severity of the issue is, old caulking may need to be removed. When it is time to uPVC repair, you must be careful not to over-caulk. This will only make your window harder to clean and lower its energy efficiency.

Verify that the drainage holes have no debris in them, and also that the sill pan is properly angled to allow the water to drain from the window. In more serious situations, you might need to consider replacing the window.

Moldy sills and rotten ones are also signs of water leakage. The fungus thrives in conditions of dampness and can spread quickly throughout the home.

It is also important to note that if the leak is coming from between the glass of your double glazing glazed windows, it is more likely to be a problem with the glass seal, rather than the frame or sliding. A uPVC specialist can easily solve this problem by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

Hinges could be at fault for the reason that your uPVC window is difficult to open or it opens in an ease. They can be easily replaced by any competent DIYer and are usually completed in just a few minutes.

Like any mechanical part hinges are prone to wear out over time. Changing a window hinge is essentially a very simple procedure, but it is easier when you have a person to assist in holding the frame in place.

Make sure that the uPVC hinges open and close in the right direction. Check for the arrows on each hinge to determine which direction the window should be opened.

The problem with the hinges on windows could be caused by improperly opening the window in a certain manner or because of inadequate installation at the factory. This issue can be fixed by sending us a photograph on our website. We will be happy to give you advice.

It is also crucial to lubricate the hinges on a regular basis. Applying an engineering lubricant that is light to the hinges is an ideal method of doing this. We recommend using the lubricant that doesn't contain solvents, like 3-in-1 Multi-Purpose oil. Regular lubrication can help the window to open and close more easily. It can also prevent corrosion and reduce the possibility of sticking. It is recommended to do this at least once a year. WD40 or other solvent-based lubricants should not be used as they could damage your uPVC windows.

5. Draughts

Draughts can be caused by different things. The hinges, Upvc Repair also due to wear and tear may become displaced, which can cause a gap to form where the sash meets the frame. This can be easily fixed by giving them a good cleaning, but if they are beyond repair it could be necessary to get them aligned or replaced. The interlock, which is on the hinge side of the window, can be misaligned. Again, it is possible to just give them a clean but in some instances it could be necessary to have them replaced.

These seals are susceptible to wear and tear or get damaged over time, allowing air to escape. This can be avoided by replacing them with high-quality weatherstripping. Replace the windows made of Upvc with low-emissivity glass. This will help control indoor temperatures and lessen the possibility of draughts.

Another method of reducing drafts effectively is to use a Draught-excluder. These are usually made of fabric tubes filled with a filler that can be put on top of your window sill. They will help stop cold air from entering and keep your home warm and cosy!

With a little maintenance and repair, your upvc windows will continue to provide an excellent level of security and insulation for your home. It is crucial to recognize that all windows have a lifespan and there may come the point when it's more economical to replace them than repair them. If you are experiencing problems with your upvc windows, it is always recommended to seek help from a professional as soon as you can.