Repairs to uPVC Windows

uPVC is a great option for modern homes. They are long-lasting, durable and easy to maintain. Unlike timber and aluminium, they don't corrosion or rot.

Cleaning and lubricating regularly UPVC windows and doors is crucial. This will help avoid unnecessary repair costs and increase energy efficiency.

1. Broken Glass

The damaged glass in your windows could cause serious damage to your home and even be fatal. You should take the time to make sure that your windows are in good working order.

Single-pane windows are relatively easy to replace and typically fit into old frames very easily. If windows with double panes are held together by internal beading, it will be difficult to remove and replace the panes that were previously in use. In this case it is essential to purchase plastic spacers to help the new pane fit into the window frame.

If you're planning attempt to remove the glass panes yourself it is important to wear the appropriate safety equipment such as gloves that are thick and protective eyewear. It is also an excellent idea to lay down a drop cloth before you start working on the glass, so that any shards fall onto the fabric instead of onto the floor, where they could be trampled on and cause further damage.

Once the glass is removed and the glass is removed, it's a good idea to cover the gap with packaging tape or duct tape to prevent water and drafts from getting into the home until a professional can come out and fix the window. This will also provide a barrier to prevent any intruders from getting into your home. If the gap between the window and the door is large, you might want to use an alarm system that has an opening. This will provide the best of both.

2. Sagging

Upvc windows and doors are an affordable energy efficient, durable and long-lasting alternative to timber sash windows. However, over time, they can suffer from a variety of issues, including sliding. A sagging window in uPVC can cause problems with light, draughts and even security. If you find that your uPVC window is beginning to shrink, it's crucial to act fast to prevent the problem from becoming worse.

Repositioning the hinges could aid in fixing a window which is sagging. You'll first need to open the windows so you can access the frame. Then, you can remove the hinges at the top and bottom using a screwdriver, and then adjust them counter-clockwise or clockwise. Close your window to check the fit after having repositioned your hinges. If you're satisfied with the fit of the window, tighten the screws to keep them in the right position.

If you can't reposition the hinges, you might require replacing the seal. Rubber seals can dry out and lose their elasticity with time, causing them to lose their tightness. If this happens, Upvc Window Repairs it's crucial to replace the seal as quickly as possible so that your uPVC windows are watertight and secure from draughts.

uPVC handles can also loosen up. The majority of the time it is due to screws that have come loose over time. However, it can occur because the handle mechanism has been worn out. Luckily, it's not difficult to repair the handle of a window that is loose yourself. First, you'll need to close your window and do an experiment to ensure that it fits. The joint at the corner of the sash should be aligned with the joint on the casing. If it isn't then you can use the screwdriver to loosen up the handle. Then, turn the mechanism back into place.

3. Water Leaks

If you wake up to wet floors and mouldy walls each time it rains it is important that you take action. Windows that leak water do can not only cause degradation of your home's structure but also undermine your efforts to control the temperature inside your home. The most frequent reason for leaks in uPVC windows is that the sealant surrounding the frame is either damaged or not present.

This is a relatively easy fix that can be done by any DIY expert. Depending on the severity of the problem the caulking that was used up may need to be removed before a new layer of caulk can be applied. It is crucial to remember that when it comes to uPVC window repairs, you should not be tempted to 'over-caulk' as this will only make the area harder to clean and reduce your energy efficiency.

Make sure that the drainage holes have no debris inside them and ensure that the sill pan is angled correctly to drain away from the window. In more extreme cases, you may need to replace the window.

Moldy sills and rotten ones are other signs of water leakage. This fungus thrives in conditions of dampness and can spread quickly throughout the house.

If the leakage occurs between the double-glazed glass, it is more likely that the problem is with the seal than the frame. A uPVC specialist can fix this issue by replacing the glass seal. This will ensure the complete insulation of your windows.

4. Faulty Hinges

Hinges could be at fault if your uPVC window is difficult to open or if it blows open with a breeze. They can be easily replaced by any competent DIYer and can usually be done within a few minutes.

Like any mechanical component hinges are prone to wear out over time. Changing a window hinge is an easy procedure, but it is easier when you have a person to assist in holding the frame up.

Make sure that the uPVC hinges open and close in the proper direction. This can be done by looking for the arrows on each hinge, this indicates which way the window should be opened.

The problem can be caused due to opening the window in the wrong way or due to a poor installation at the factory. Sending us photos via our website will often resolve the problem. We are more than happy to provide advice.

Regular lubrication of the hinges is also necessary. Applying an engineering lubricant that is light to the hinges is an ideal way to do this. We suggest using a lubricant that does not contain solvents, like 3-in-1 Multi-Purpose oil. Regularly lubrication will help the window replacement near me open and close more easily. It can also lower the chance of windows sticking and help prevent corrosion. This must be done at a minimum once a year. WD40 or other solvent-based oils should not be used as they could damage your uPVC windows.

5. Draughts

Draughts can be caused by a variety of different things. First, the hinges due to wear and tear can become misaligned, this can cause an opening to appear between the sash and the frame. If they are beyond repair, it could be required to realign them. In addition, uPVC window repairs the interlock could also become misaligned. This happens on the hinge's side and may need to be cleaned. In some cases it might be necessary to replace them.

The next most common reason for draughts are the window seals. They can become worn down or damaged over time and will allow air to escape through the gaps. Installing high-quality weatherstripping can help stop draughts. Another alternative is to replace the upvc window with low-emissivity glass. this will help to regulate indoor temperatures and will lessen the risk of draughts.

One of the most effective ways to reduce the draughts in your home is to use an draught excluder. These are usually fabric tubes which are filled with a type of filler. They can be put on the top of your windowsill. These will help to stop cold air from entering and keep your home warm and cosy!

Your upvc windows can keep providing excellent insulation and security to your home by performing regular maintenance and repairs. It is important to remember that all windows will eventually get worn out and it is more cost-effective to simply replace them instead of fixing them. If you are experiencing issues with your window made of upvc, it's best to consult an expert as soon as you can.