UPVC Window Handle Replacement

Replacing a damaged window handle is a easy task and, with the right tools, it can be accomplished quite quickly. However, it is essential to identify the type of handle and its spindle's length prior buying a replacement.

Older uPVC window handles have a spur that protrudes and locks over a wedge striker. These can be either left or right-handed and must be to be replaced with the same handle.

What type of lock and handle do I have?

There are a myriad of window locks and handles made from upvc, each with its own advantages and purposes. The type of handle you are using will determine how easy it is to open your double glazed windows replacement and if the locking mechanism works as intended. Over time and through regular use, window handles made of upvc are prone to wear or damage. out, making them less secure and effective. In some instances they might even be completely removed. It is important to repair the handles on your window made of upvc when you see they are falling off. This will help prevent potential break-ins and protect your home from burglary.

It's a simple job that anyone can complete. You'll need a few tools, but with appropriate knowledge, it's a straightforward process that should take only a couple of minutes. To get started, you will need to identify the type of handle and lock you have on your upvc window and then identify the best replacement.

Inline Espagnolette Handles

They are typically located on the side of the window. They are flat in design and feature an opening that is connected to the locking mechanism on the window frame when turned. Inline upvc handles also have spindles that run through the center of the handle and upvc Window Handle replacement into the frame of the window to activate the latch.

Cockspur Handles

These handles are usually found on older uPVC window frames. They have distinct hook-shaped designs. Cockspur handles are fitted with a single screw that holds the handle to the frame and aren't as secure as other kinds of window handles.

Tilt and Turn Handles

As opposed to the other handles made of upvc, tilt and turn handles can both be rotated to open the windows and tilted inwards to allow ventilation. In general, they feature a 7mm spindle on the back of the handle. They are available in left and right-handed versions.

When buying replacement upvc handles, it is important to measure the spindle's length since not all of them are identical in size. Drop something in the middle of the hole to measure the length. This is the maximum spindle size that will fit your windows.

What is a spindle?

uPVC window handles operate similarly to doors. By turning the handle, you are able to open a latch in the frame. The window then opens and shut. But, at times, these handles can become damaged, especially when they are used frequently or exposed to harsh weather conditions. This can leave you needing to replace your uPVC windows handles as they may not be able to operate the window in a proper manner anymore.

There are a variety of uPVC handles to choose from, including Espag, Cockspur and Spaded handle options. These handles are designed to fit inside the uPVC frames in different ways and each handle type utilizes a specific spindle to secure the mechanism into the window. It is essential to determine the kind of handle that is installed on your uPVC windows so that you can replace it with a suitable one.

The base section of the handle will tell the type of uPVC it is. A snap-in cover should be over the screw that holds the base of the handle in place. After removing this, you will be able see the screw that holds the base of the handle in position. After both screws are removed, you should be able pull the handle from the uPVC.

Once you have removed the uPVC window handle you need to carefully remove the spindle that was previously attached to the locking mechanism. Take note of the length of the spindle. You will need to purchase a replacement with the same length as the handle that was originally used and the locking device.

The spindle wears out and cannot operate the locking mechanism. This could be due to damage caused by constant use or a loosening of the locking mechanism or even rust over time. When this happens it will be necessary to replace the window handle and locking mechanism to restore complete functionality to your uPVC windows.

How do I take off the handle that was previously attached?

Window handles can become damaged or broken over time. It is important to fix them as soon as you can to ensure your safety. It is easy to replace a damaged or worn handle. The task can be accomplished in less than an hour without the need for any special tools.

To remove the old handle, you must first remove the screw that is located at the base of the handle. Once the screw is removed, the handle can then be removed from the base section. A second screw will be located at the base of the handle. This too can be removed. Once both of these screws are removed, the handle can be removed from the base portion of the window.

After removing the handle and align the fixing holes of the new handle with the existing holes in the window frame. If there is a sticker or cap on the new handle, take it off it if needed and screw the handle in the appropriate position. Once the handle is set, it is essential to check whether it functions by turning the handle, and ensuring that the lock mechanism activates.

Espag handles have spindles that extend from the handle and slot into the multipoint locking mechanism that is on the window frame. Cadenza windows come with an edge with cut-outs which slot into the lock mechanism while Cockspur handles have an extended nose that hangs over either the frame's outer or the transom bar cross member within the window.

Once you have the new handle in place, insert the spindle inside the lock inside the window and then tighten it. Replace the snap-in cover and screw cap (if appropriate) after the handle is securely fixed. Once the handle is ready to use, simply open and close the window a few times to make sure that it functions correctly and securely.

How do I fit the new handle?

Changing your uPVC window handle isn't difficult, and the process is quite simple. All you need is a screwdriver, and a bit of patience. First, make sure the old handle is unlocked. Then, remove any visible screws. You can also replace them using screw caps. After removing the handle you will need to note the length of the spindle that extends from the back. This is important as it will determine what kind of handle to buy.

Espagnolette handles are the most popular kind of handle that is used on uPVC windows. They have a spindle which runs through the handle, and is responsible for an internal locking mechanism within the frame of the window. When the handle is turned, it opens the latch on the window and allows it to open. When used regularly and time, handles made of espagnolette can be damaged.

Cadenza handles are a kind of uPVC handle that is commonly used in tilt and turn windows. They have a protruding knife that is operated by a multi-point locking mechanism inside the window. They are more secure than the espagnolette handles since they only open from the inside. They can be replaced using the same method as you would for espagnolette handles however, ensure that the new handle is angled and not flat.

Once you have decided on the right handle for you then you can align the new handle with the existing screw holes and then screw it in the appropriate position. Then, you should put the screws on and test the new handle. You can perform this by dragging the handle back and UPVC Window Handle Replacement forth from the locked position to the unlocked for a few times. If you experience any issues, it may be worthwhile contacting a professional to see if they are able to assist in resolving the issue. They can offer advice on how to fix the issue in a quick and effective way.