Peugeot 208 Key Replacement

Peugeot 208 key replacement is best left to professional auto locksmiths with the right equipment and technical know-how. They will be able to create and program new keys much quicker than a dealership and at a lower price.

A dead battery for your coin is most likely to blame if your key fob stops locking or unlocking the doors. There are other possibilities that the key is malfunctioning.

Dead Coin Battery

A dead coin battery will stop your Peugeot 208 from locking and unlocking, as well as making it impossible to start the engine. In this situation you'll need employ the alternate method of starting found in your vehicle's owner's manual.

Another reason why your 208 might not be starting is because the spark plugs are worn down. The spark plugs are responsible for igniting the fuel that powers the engine. However they have a short life span. They'll eventually fail when they aren't used enough.

There is an easy solution to this issue. Examine the voltage of your battery using a multimeter. If the voltage is below 11,5 volts, it's the time to replace it. If the battery has corrosion it is necessary to clean its contacts. You can do this by lifting the rubber covers covering the two terminals of the battery and using wire brushes to clean any corroded areas of the battery. Then, you should connect the cables for the positive and negative poles.

Water Damage

If your 208 isn't starting and the battery is not empty, you must ensure whether the spark plugs are in good working order. It is possible that they are just overly filthy, making them unable to spark. The spark plugs can be cleaned in the workshop.

Peugeot cars use a transponder style key that integrates with the car's immobiliser system. This makes sure that only the correct key can start the engine. If the chip inside the Peugeot key is damaged, then it will not send the proper signal to the vehicle.

This is a typical issue that is often caused by water damage. This is particularly common in colder climates. the vehicle may have been exposed to rain or snow. If this is the case, you should contact a reputable auto locksmith who has all of the tools and equipment required to modify the new key. They also have the latest technological know-how and the equipment required to create a peugeot 308 key fob 208 smart key. The process shouldn't take more than 15 minutes.

Contacts for the battery that are defective

Peugeot changed from the carbon-encased transponder chips to a new type of chip that relies on electronic components that are placed on circuit boards. The new system is fantastic when it's brand new, but the circuit boards wear out over time and stop working properly.

This could stop the immobiliser chip from activating the immobiliser chip, causing your car not to start. If this happens, it's a good idea to contact a Peugeot specialist or locksmith.

Another common issue is when the battery in the key fob is dying, this causes the key blade to stop from entering the lock. A car locksmith will replace the battery and then cut a fresh blade for you. This is a quick solution.

Faulty Receiver Module

If your Peugeot key fob has stopped working after dropping it on the floor, or being exposed to a sudden rain or accidently washing it may be due to a faulty receiver module. The receiver is responsible for sending radio frequency signals to the onboard computer which controls the centralized locking system inside your Peugeot vehicle.

The rubber seals on the key fob prevent water from reaching the electronic chip. However prolonged exposure to water can break through these seals, causing damage to the chip. The high salt content of the ocean water or pool can cause damage to the key fob if it is submerged.

If your Peugeot spare key fob stops working You'll need the module replaced. This can only be performed by a professional auto locksmith or Peugeot specialist. As opposed to other cars, peugeot replacement key fob keys are protected by an exclusive immobilizer system that requires the correct programming to start the engine. This is the reason that you should only trust the Peugeot locksmith to design and program a replacement.

Computer malfunctioning on-board

The on-board computer in your Peugeot is responsible for many of the features in your car, including airbags and power windows. If something is wrong with these systems, they will usually display a code indicating the issue. The code is stored within the system until the problem is fixed. Usually, this will mean the on-board computer being replaced.

The most common cause of the warning light for the airbag to turn on is corrosion or loose connections in the sensor. This can be caused by wear and tear, ageing, or exposure to salt and moisture. This issue should be addressed as soon you can, because an airbag that is not functioning could pose a risk in the event of an accident.

If your Peugeot is showing a card that is not being detected error, then the key battery inside the key fob could be weak or dead. This will stop the key fob sending a signal to disarm the immobilizer on your vehicle. You can test this by pressing the unlock button on the key fob and then attempting to start your vehicle. If this fails, then the key battery will need replacing.