Peugeot 208 Key Replacement

It is better to leave the replacement of Peugeot keys 208 to auto locksmiths equipped with the required equipment and skills. They will be able to make and program new keys faster than a dealership would and at a lower price.

If the key fob has stopped locking or unlocking your doors, it is likely due to a dead coin battery. There are also other reasons that the key might be malfunctioning.

Dead Coin Battery

A dead coin battery will prevent your Peugeot 208 from locking or unlocking, and cannot start the engine. In this case you'll need to use the alternative starting method found in your vehicle's owner's manual.

The spark plugs may also be worn out. Spark plugs are what ignite the fuel to start the engine. However they are limited in their lifespan. They'll eventually degrade if they're not used enough.

There is an easy solution to this issue. Examine the voltage of your battery using a multimeter. If it is below 11.5 Volts, then you need to replace it. If the battery has corrosion it is necessary to clean its contacts. You can do this by lifting the rubber covers that cover both battery terminals and using wire brushes to clean any parts that are corroded from the battery. You should then reconnect your cables to connect the positive and negative poles.

Water Damage

If your 208 does not start and the battery hasn't been replaced, you must look at the spark plugs. It could be that they are simply too dirty and do not spark. The spark plugs can be cleaned in a workshop.

Peugeot cars use a key with a transponder compatible with the immobiliser. This ensures that only the right key can turn the engine. If the chip inside the Peugeot key is damaged, it won't send the correct signal to the vehicle.

Water damage is a common cause of this problem. This is a common issue in areas with colder temperatures where the vehicle has been exposed to rain or snow. If this is the case, contact a reputable auto locksmith who has all of the tools and equipment required to reprogram the new key. They also have the most up-to-date technology and the machinery needed to make the Peugeot 208 smart key. The process shouldn't take more than 15 minutes.

Faulty battery contacts

Peugeot changed from the old carbon-encased transponder chips to a brand new type of chip that uses electronic components within circuit boards. The new system works great in its initial state, but the circuit boards degrade over time and cease to function properly.

This could stop the immobiliser chip from working the immobiliser chip, causing your car not to start. Contact an Peugeot specialist, or a locksmith if this is the case.

The most frequent issue is when the battery in the key fob starts to fail. This causes the blade of the key to stop feeding into your lock. A locksmith for cars will replace the battery, and then cut a new blade for you. This is a simple solution.

Faulty Receiver Module

It could be that the receiver module has a problem If your Peugeot key fob doesn't work after being dropped on the floor, exposed to a sudden downpour or accidentally washed. The receiver is responsible for sending radio frequency signals to the on-board computer which controls the centralized locking system inside your peugeot replacement key fob vehicle.

Rubber seals on the key fob stop water from getting to the electronic chip. However, prolonged exposure to water could be able to penetrate these seals and cause damage to the chip. Submerging the key fob into ocean water on the beach or throwing it into the pool could be particularly damaging due to the high salt content.

The module needs to be replaced if your Peugeot spare key is no longer working. This can only be done by an Peugeot specialist or an expert auto locksmith. peugeot 207 car key (check out here) keys, unlike other cars, are secured by an immobilizer device. This requires the correct coding to start the car. This is why you should go with a knowledgeable Peugeot locksmith for the job of designing and programming the replacement.

Faulty on-Board computer

The on-board computer inside your Peugeot is responsible for many of the systems in your car, ranging from airbags to power windows. If something is wrong with these systems, it'll typically display a code that identifies the issue. This code will be saved in the system until the issue is fixed. This will often require the on-board computers to be replaced.

One of the most frequent causes of the airbag light coming on is loose or corroded connectors in the airbag sensor. This could be due to wear and tear, aging, or exposure to salt and moisture. This problem should be addressed as soon as you can, since an airbag that is malfunctioning could pose danger in the event of an accident.

If your Peugeot is showing a card that is not being detected error then the key battery inside the key fob might be dead or weak. This could prevent the key fob from transmitting a signal that will disable your vehicle's standard immobilizer. Test this by pressing the unlock key on the fob's key, then trying to start your vehicle. If this does not work then the battery in the key will need replacing.