Peugeot 208 Key Replacement

Peugeot 208 key replacement is best left to professional auto locksmiths who have the proper equipment and technical knowledge. They can create and program new keys faster than a dealership would and at a lesser cost.

If your key fob stopped locking or unlocking your doors it could be due to a dead battery in the coin. There are other reasons the key could be malfunctioning.

Dead Coin Battery

A dead coin battery will stop your Peugeot 208 from locking or unlocking, and cannot start the engine. If this is the scenario, you'll need use the backup starting method that is detailed in the owner's manual of your vehicle.

The spark plugs may also be worn out. The spark plugs ignite fuel to start the engine. They are only able to last for a short time. They'll eventually fail if they're not used enough.

Luckily, there is an easy solution for this issue. Check the voltage of the battery using a multimeter. If it's less than 11.5 Volts and you are not satisfied, then it is time to replace it. It is also essential to clean the battery's contacts in case it is corroded. You can do this by lifting the rubber covers covering the two terminals on the battery and using a wire brush to remove any corroded components of the battery. After that, you need to connect the positive pole cables to the negative.

Water Damage

If your 208 does not start and the battery has not failed, you should examine the spark plugs. It could be that they are just overly dirty, which causes them not to spark. The spark plugs can be cleaned in an workshop.

Peugeot cars are equipped with a key with a transponder compatible with the immobiliser. This ensures that only the correct key can turn the engine. If the chip in the Peugeot key is damaged, it will not send the proper signal to the vehicle.

Water damage is a typical cause of this issue. This is a common issue in more cold climates where the car is exposed to snow or rain. If this is the case, seek out a reputable auto locksmith who will have all the equipment and tools needed to change the key's programming. They will also have the most up-to-date technology and equipment needed to create the Peugeot 208 smart key. The process should take no more than 15 minutes.

Contacts to the battery are not working properly.

peugeot 206 key replacement changed from the carbon-encased transponder chips and introduced a new key for peugeot 207 type of chip that uses electronic components within circuit boards. This new system works well when it's fresh, however, over time, the circuit boards start to lose their effectiveness and cease working properly.

This could stop the immobiliser chip from activating the immobiliser chip, causing your car not to start. If this is the case, it's recommended to call a Peugeot specialist or locksmith.

Another issue that is common is when the battery of the key fob starts to die, this causes the key blade to stop getting into the lock. A locksmith from your vehicle can replace the battery and cut a fresh blade for you, this is generally a quick fix.

Faulty Receiver Module

If your Peugeot key fob isn't working after dropping it on the floor, getting exposed to a sudden downpour or accidently washing it may be due to a malfunctioning receiver module. The receiver is responsible for sending radio frequency signals to the onboard computer that controls the central locking system of your Peugeot vehicle.

Rubber seals on the key fob keep water from getting to the electronic chip. However prolonged exposure to water can cause damage to these seals and the chip. The high salt content in the pool or ocean waters can cause damage to the key fob, especially if it is submerged.

If your Peugeot spare key fob isn't working, you'll need to have the module replaced. This can only be done by an Peugeot specialist or expert auto locksmith. Peugeot keys are, unlike other vehicles, are secured by an immobilizer system. This requires the right codes to start the car. This is why it is imperative that you should only trust an authorized Peugeot locksmith to create and program a replacement.

Computers with faulty on-board computers

The on-board computer in your Peugeot is responsible for a variety of features in your car, including power windows and airbags. If something goes wrong with these systems, they will usually show a code that identifies the issue. This code will be saved in the system until the issue is resolved. This may require the on-board computers to be replaced.

One of the main reasons for the light turning on is the loose or corroded connections in the airbag sensor. This could be due to wear and tear, aging, exposure to moisture and salt. This problem should be addressed as soon you can, since an airbag that's malfunctioning could be dangerous in case of an accident.

If you encounter an error message stating that the card is not found on your Peugeot key fob, the battery inside the key fob may be weak or dead. This will prevent the key fob from sending a signal to disable your vehicle's immobilizer. You can test this by pressing the unlock button on the key fob and then attempting to start your car. If this fails, then the key battery needs to be replaced.