Reasons Your fiat 500 replacement key cost 500 Key Fob Won't Work

A key fob with the fiat 500 number is a convenient method to unlock the doors and get started the car. However, there are numerous reasons why the fob won't be working. This includes a dead battery and water damage, as well as problems with receiver modules, as well as interference.

This listing is for an NEW replacement Fiat Flip Key Remote that is similar to the Ilco brand. It needs to be professionally programmed (click here to find local locksmiths for automotive locksmiths). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

The most common reason the 500 key fob won't function is due to a dead battery. Modern key fobs operate with a limited operating range, and must be within some feet of the vehicle in order to function. If you're far from your vehicle and push the keyfob button it will not respond and display the message "Key Fob Not Detected".

If this happens, replace the battery in the coin cell (Part number CR2032) by a new one from a reputable brand like Panasonic, Duracell, or Energizer. They are usually available in your local hardware store, or online.

You can test the coin-cell battery by pressing the buttons while standing close to your Fiat 500. The car should blink its parking lights and the key fob will operate the lock and unlock buttons.

If the key fob doesn't work after replacing the battery, it might be damaged by water, which prevents it from communicating with the receiver module in your vehicle. Water damage can occur in a variety of ways, such as the simple splash or submerging the key fob saltwater at the beach. If you suspect that your fob has been exposed to water, put it in a dry rice bag to draw the moisture out. If this doesn't work your fob may need to be reset by a professional auto locksmith or the dealer.

Water Damage

The fob does have rubber seals that keep water from the electronic chip inside and out of the ocean or washing it in a machine could cause water damage. Saltwater can cause the circuit board to become shorted and eventually end up dying. In the event that you let your fob get wet, it's not an ideal choice, but if you drop it in a cup of water or don't remember to remove it from your pocket before you run the washer, don't give up hope.

First, remove the battery. Clean the electronic chip using isopropyl alcohol or another similar product and dry it thoroughly before replacing the battery. Check the fob again to check if it's working. If the fob doesn't work, it may need to be changed. This is usually done by a dealer or professional auto locksmith.

If your key is older and not programmed for your car You will need to replace it completely. This is a straightforward process that can be completed by a professional automotive locksmith. The locksmith will require the key to be cut to match the car's ignition. They will also need to reprogram the fob in your car's system. It's a simple and inexpensive process that is usually completed within the same day.

Receiver Module Issues

Your 500 key fob may not function because it's out of range. The remote usually has an operating range of 30 feet or less and if it's far away from your car it will not respond to your commands. You can easily solve this problem by moving the remote closer to your car until it responds.

If you've replaced the battery in your coin (commonly known as"button" or "button" or "watch") and your fob doesn't function, it could have an internal circuit board issue. Reprogramming the fob typically resolves the issue. You can find the instructions for the majority of vehicles on YouTube or in the owner's manual.

It is possible to replace the metal clips that hold the coin batteries in their place. If they lose tension, it can stop your coin battery from sitting properly, workshop causing your remote to malfunction.

In rare cases the fob might be out of sync with your vehicle because of hardware or software issues. It is possible to fix this issue by visiting your local dealer or auto-locksmith to reprogram your key fob. In some instances the software may require reinstallation into your body control modules.

Interference

In addition to a dead battery on a coin The key fob might not be able to transmit or receive signals due to interference. This can happen when the key fob is located near radio transmitters (cell phones and radar detectors) or another source of electromagnetic radiation. The key fob could not work because of a problem to the buttons or water damage, or damage to the internal chips.

If the key fob has been unable to function for a while suddenly and you've tried everything you can do at home to resolve it e.g. You may have a faulty 500 receiver module in the event that you've tried replacing the battery, reprogramming, or using an alternative key fob. The receiver module is situated under the dash, and it picks up the radio frequency signals from the key fob. It transforms the signals into electronic commands which are then processed by the vehicle.

Fortunately, there's an easy method of resetting all of the on-board systems in your 500, including the key fob. Disconnect the battery for 15 minutes by removing first the negative cable, then the positive cable. Then reconnect the battery. This will remove any remaining electrical charge and restart the car's computers, which could help the key fob to function again. If the issue continues, you should seek the advice of an expert technician. They will be able to identify the root cause of your issues.