Reasons Why Your Nissan Qashqai Key Fob Won't Work

The Qashqai's bigger dimensions give it a distinct SUV-like ambiance. Its 19-inch alloy wheels on Ti and STL versions may also be firm. The front tyres of the Qashqai can lose grip on rough surfaces and its CVT could occasionally exhibit wrist-flexing torque steer.

This is usually due to an inoperable coin battery, which is easily replaced in a matter of minutes. Make sure the battery you replace is of the same voltage, size and specifications.

Water Damage

One of the main reasons that a Nissan key fob will give the "key ID is not correct" message is due to water damage. The key fob comes with rubber seals which protect the chip inside, but long-term exposure to moisture can cause it to stop working properly. This is usually the case when you've dropped your key fob in the ocean or a pool pool, but it can occur if it becomes wet due to rain or soapy hands.

If your key fob was exposed to water for a long period of time then you might need to clean it with isopropyl or electronic cleaner. Or, it could need to be taken to an expert for repair or replacement.

If your key fob does require replacement the process is simple. First, make sure that you have an appropriate multipack battery (CR2032 3V). Unlock the front and rear cases with the flat-head screwdriver. You'll need to remove the metal retaining clips and remove the old battery and insert the new one. Reassemble the fob and replace the mechanical key. Check that it works correctly. If not it, you'll need to bring it to an nissan key fob replacement dealer or professional auto locksmith to replace the chip. Fortunately, the chip is not normally damaged by exposure to water and therefore this shouldn't be a major expense.

Dead Coin Battery

The coin battery is a second frequent reason why your Nissan Qashqai remote key fob may not work. These batteries last three to five years, but can become faulty over time if the fob has been dropped often. You can replace the battery, however, make sure it's the same voltage and same size as the previous. If you choose to use a brand new battery, it may cause the key to be assigned a different key ID. This will prevent it from being linked to your vehicle.

The best method to replace the battery in a Nissan Qashqai key fob is by removing the fob with an incredibly small screwdriver with a flat head. The screwdriver should be inserted into tiny notch at the bottom of the fob and turn it around gently to separate the two parts of the key fob. Remove the old CR2025 battery and replace it with a new one, making note of the position of the old battery in the fob.

Before you put the new battery into place ensure that there is no water damage or dirt on the terminals. If there is, wash the terminals using a small amount of isopropyl alcohol. You should also ensure that the pole cables are connected correctly - they should be connected to the negative and positive poles of the battery respectively.

Troubleshooting

If your Nissan Qashqai's primary fob doesn't function after exposure to water that is clean from a tap or rain, this could be a sign there is a problem with the internal chip. You'll need a new keyfob in the event that you can't resolve the issue by changing the battery. If you dropped the key fob on the ground and it stopped working right away it's most likely because it has damaged the internal chip. You can usually get the key fob to work again if you remove and clean the chip with alcohol and paper towels before putting it back into.

Key ID Incorrect is a common error that can be seen on the dashboard of your vehicle. The vehicle is not able to recognize the key fob, which is why it won't allow the vehicle to start. This problem could be caused in various ways, including water damage, problems that are undetectable in the key fob circuitry or RFID interference.

The key fob will stop working if the 12 volt batteries are dead or do not provide enough electrical current. This could affect the remote keyless system as well as central locking in your Nissan Qashqai, as well as stopping you from starting the engine with the key fob (if equipped with Intelligent Key). If you can't lock or unlock the door manually, you should check the batteries inside your key fob to make sure they are in good shape. You may also try reconnecting the battery in order to reset your transmitter.

Reprogramming

If the key fob was not submerged in saltwater it should be able to return to life by a simple wash of clean water. You may also try cleaning the electronic chip using isopropyl Alcohol or an electronic cleaner. If none of these work then you might need to replace the key fob.

If your Nissan Intelligent Key is still not functioning, there may be an issue with the connection between it and your car. Start by turning the ignition key but not beginning the car. Continue this process until the hazard lights flash twice. Turn the vehicle off and remove the keys.

Then, you need to then open the fob compartment in your vehicle. It's usually located in the door jamb, on the handle for the driver's door or underneath an armrest. Locate the small button labeled "program" and press it. Once the process is completed, you should hear an emitted sound.

It's time to put your Intelligent Key to the test. Click all the buttons on the key while you are at a distance away from the car. If the lights flash or the horn sounds, then the key is successfully connected to the Nissan. You can also test it near the Nissan.