How to Replace a Hyundai I10 Key Fob Battery

The Hyundai I10 sports a sleek interior that rivals the Volkswagen UP, Citroen C1, and SEAT Ibiza. Its interior is better quality than its rivals such as the Citroen C1, Volkswagen UP and SEAT Ibiza.

Hyundai's key fob does lots of work for you, such as locking and unlocking your vehicle remotely. It also includes a mechanical key that you can use in case the battery in the fob fails.

Dead Coin Battery

The key fob enables drivers to lock their cars and start them without having to insert a physical key into the ignition. It accomplishes this by using radio frequency signals that communicate with the vehicle's onboard computer.

The battery inside the key fob is responsible for this message and will eventually degrade and will require replacement. Depending on the model of your Hyundai, it may or not display warnings before the battery is dead. It is recommended to keep a spare key fob around with you in order to quickly replace the battery if it starts to wear out.

After the new battery is installed the key fob needs to be reprogrammed in the car. It is possible to do this using an OBDII or Hyundai Digital Key scanner, however, it is generally easier to do in your Reno home. Follow the steps in the owner's manual or look on YouTube for "how to open and replace a Hyundai keyfob battery." Make certain to take a photograph of the old battery or write it down prior to removing it.

Once the key fob is changed, it should work again. If it doesn't work, you will need to go to a dealer for a replacement or contact a locksmith. They will have the experience and tools to fix the issue.

Water Damage

A key fob is a useful piece of technology that can allow you to lock your car from the comfort of your home, slide down the windows from outside and even begin the vehicle. It is not indestructible and will eventually wear out due to normal usage. Fortunately, the process of replacing the battery of a Hyundai key fob battery is relatively straightforward and affordable.

Dropping your key card in an puddle, a pool or even the washing machine isn't atypical and is often salvaged, but only if you act quickly. A wet key fob is bad for electronics. It could cause corrosion, short-circuits, and even failure.

The first thing you must do is try to squeeze as the most water out as you can. Shake any visible moisture out by flipping the fob. You can also utilize a hairdryer or put it on the radiator to speed up the drying process. After you've removed all moisture you can, consider placing the fob in a place that is warm and dry where it will continue to dry for a couple of days.

Then, you can open the fob in order to remove the old battery. Most Hyundai i10 keys have the same type of battery that is used in many quartz watches, and are usually very easy to replace. After replacing the battery, take a photograph or note the position of the battery prior closing the fob.

Poor Battery Contact

The battery in your key fob could be worn out. This is a common problem, and usually the remote starts showing indications of trouble long before it gives up completely. Make sure that the retainers are secure and do not have any corrosion on them. If they do, clean them with a suitable battery cleaning solution and wire brush. Make sure you use a button-cell that has the same size, voltage, and specification as the original.

This could also be a sign that your alternator is not working properly. The alternator is the component that charges your battery while you drive. A malfunctioning alternator can drain the battery quickly and cause the warning light to come on.

A quick test of voltage will aid in determining if this is the case for your Hyundai. If the battery is working, the problem could be related to the circuit board or any other component of the key fob. You can access the key fob by pressing a small metal tab, or button on either the back or front of the device. After you take off the cover, insert a new CR2032 battery and make sure that all the connections are in contact.

Reprogramming

Hyundai provides keyless entry on several of its models. This makes cruising around Littleton and Parker, repair CO, easier than ever. If you own a key fob that you can use to unlock and lock your car's doors and start the engine with the remote. But, it's not completely safe and a broken fob can lead to problems. If your Hyundai key fob stops working it might require reprogramming to work with your vehicle.

The first thing to do is take the battery off. The button cell battery is typically contained in a tab made of plastic. When you open the tab, make sure you replace the battery with a battery that's the same voltage and size as the one you had previously.

Once the battery is replaced, close up the tab and replace the clips that hold it. Then examine the key fob to see whether it's working.

If the key fob is still not working, you may need to contact a locksmith or dealer. A dealer or locksmith can make a new key and remote for you, and can also program the key to work with your vehicle. This service is usually paid for, but it's worth it if your goal is to keep your Hyundai key fob in good working order. They can also help you in finding the right hyundai i10 key fob key fob for your requirements.