Fiat 500 replacement fiat 500 key Key Fob

If your 500 remote key fob has stopped working, it's time to replace the battery. If you replace the battery, but it's still not working, the problem may be somewhere else.

At United Locksmith, we specialize in making new keys for old cars. We have the tools and parts needed for this job.

Dead Coin Battery

A dead battery is the primary cause of your fiat 500 key replacement cost 500 keyfob not locking or unlocking the doors. The battery inside the key fob can be depleted quickly if you don't use it frequently enough. If your remote started to show signs of weakening such as a loss in range and then completely stopped working it is likely that the battery is dead.

Metal clips keep the battery in on the key fob. If the clips aren't tight enough, they can cause problems with contact, which can prevent the remote from receiving power. Utilizing a small screwdriver, push the retaining clip outwards to remove the current battery and replace it with a new one. Make sure to use a battery with the same size, voltage and specifications as the original.

Water exposure can cause the key fob to become corroded or damaged. Even a quick bath in warm, soapy water can cause damage to the chip. Make sure your key fob is dry.

Water Damage

Water damage could be the cause of your key fob not working properly. Key fobs are fitted with rubber seals that prevent them from being damaged by light rain or splashes of water, however it is very important to keep your keys from being tossed into the ocean, pool, and washing machine!

The key fob contains an electronic chip inside that transmits a signal to your car's immobilizer system. This is what allows your 500 to start or lock, however should the chip become saturated, it won't be able to longer work.

If you want to check whether your key fob functioning it is possible to clean the internal electronics using isopropyl or an electronic cleaner. It is recommended to replace the key fob when it's submerged into salt water, rather than trying to fix it yourself.

While a replacement fob might cost you a bit of money, it's a lot cheaper than paying for your Fiat 500 to be towed to the dealer and repaired! You can also make it yourself in just only a few steps. Be sure to have the correct battery type prior to opening your keyfob. This task is far simpler than it appears and you can find step-by-step directions online for virtually any key fob for your car.

Faulty Chip

The chip in the key fob connects directly with the immobiliser of your car to ensure that your vehicle will only start when proper keys are inserted. If the chip is damaged or damaged in any way, your car will not start.

A chip that is defective can happen due to a variety of reasons, but the most common cause is water damage or the battery being dead. It is best to delegate the job to a professional locksmith who can replace the chip quickly and at reasonable cost.

If your key fob ceases to function after exposure to clean tap water or rain, take off the battery and clean the electronic component with a paper towel to ensure that it is completely dry before putting it back into. If the key fob still doesn't work, it is likely a fried chip and will need to be replaced.

A few people will visit their dealer if they require an entirely new Fiat fob. However, this can be expensive. If you're seeking a cost-effective solution to get your Fiat key fob repaired, look no further than United Locksmith. We have the tools and experience needed to fix your fiat 500 key Fob - www.chumphonburihos.com - fob in a professional and timely way.

Faulty Receiver Module

Fiat key fobs send an alert up 50 feet to the vehicle, which can unlock and lock the doors (and start the vehicle for those with automatic transmissions). There are a few reasons why a fob could not function. This could be due to a dead coin battery or water damage buttons, worn ones, a receiver module issue and signal interference, or a malfunctioning electronic chip.

If the fob is in a pocket which has been subject to extreme trauma, such as falling on hard floor or being washed in a washing machine or dishwasher, it might not be capable of communicating with the car's Body Control Module (BCM). The BCM is a security system which will only accept signals from genuine keys.

If this is the case, then you will need to replace your fob. A professional locksmith is able to handle every aspect of the replacement process and even program a new one for your 500. They can even provide a clone fob that works exactly like the original (and costs just one-third of what it would cost).