How to Replace a Kia Sportage Replacement Key

The key on many Kia models has a keyless entry system built in. The key can be compared to an remote control, and can be changed with a fresh one from an Kia dealer or a locksmith.

Key fobs may stop working due to a variety of reasons, including an empty coin battery, worn buttons or buttons, water damage, signal interference, and a defective receiver module. Here are some suggestions on how to get your Kia Sportage replacement kia key key working again.

How do you replace a remote key or smartkey

It doesn't matter if your Kia comes with an intelligent key, remote key push-to-start key, or a standard non-transponder key made of metal The battery inside these keys will eventually need replacing. This is especially when your car displays a message indicating that the remote or smart keys are in poor condition.

This is a relatively simple process. To replace the battery on the keyfob remove the mechanical key from the slit at the back of the fob. Then, you need to pry the cover open. A small screw is located inside the key fob, which holds the battery in place. Using a small screwdriver, take the screw off and pull out the old battery. Then, insert the new one and close the slit on the key fob.

Once the key fob has new batteries and you've tested it, press the lock and unlock buttons. It's good in case the doors lock and unlock as expected. You can now use the hands-free feature to lock and unlock your Kia whenever your fingers become cold or you need to complete errands in Brandon.

Not all key fobs may need to be programmed (transponder chips or smart keys). This requires a programming machine that is available only to the automotive locksmith or dealer. Other keys (non transponder keys made of metal) do not require programming. If your keys need to be programmed, you must be aware of the key code printed on the tag that identifies the key and then record it in a safe location.

How do you replace the battery?

If your Kia key fob isn't responding when you press the lock or unlock button on the fob, it is a good indicator that the battery should be replaced. A low battery may also cause other issues, such as the check engine light flashing on or the engine not cranking. Fortunately, replacing the battery on the key fob is a fairly simple DIY project that requires just a few tools.

Before starting the process ensure that your vehicle is off and that all doors are shut. Find the small metal or plastic piece at the bottom of your key fob and jiggle it until a metal key slips out. This key can be placed inside the driver door handle to unlock your car.

To replace the key fob battery, take off the rear cover and use a plastic pry bar tool to remove the latch holding the black negative battery cable. Remove the old battery, and then align the new battery to ensure that the "+" positive side faces you and the "-" negative side is facing towards the fob's metal electrical contacts. Push the new CR2032 battery straight into position without putting too much force on it to avoid damaging or bending the contacts made of metal.

After the new battery has been installed after which you turn the key fob off and then turn it on in the ignition until the door locks. Then you can test your Kia key fob and see if it is working properly again.

How do you replace the smart key

You may have either a standard keyfob or a Smart Key depending on the model of Kia Sportage. The difference between these is that the smart key has a small mechanical key blade in it, whereas the standard fob isn't equipped with. Both types of key fobs are equipped with batteries inside which eventually needs to be replaced. This is an easy process that takes less than two minutes.

Before you begin it is important to make sure that you are on a level surface with good lighting and that your Kia is turned off. Keep in mind that the fob has tiny parts that could fall in the event of a mishap.

The first step is to find the small release button that is located on the backside of the fob. It will be an oval or circular slot. After pressing this button, the mechanical key blade will pop out and you will be able to open the key fob.

Once you have the key fob opened and you are able to remove the old battery, and replace it. The new battery is the CR-2032, and it can be purchased online or in your local auto parts shop. After you've finished, your key fob should allow you to lock and unlock your vehicle, even if it isn't running.

How do you replace the mechanical key

The Kia key fob is an amazing convenience that lets us lock and unlock our car with the press of a button. As with all devices it is possible that the Kia key fob can have issues at times. There are ways to fix these problems and keep your key fobs functioning for many years.

A dead or weak battery is one of the most common problems. This can cause your device to stop working or operate intermittently. If this is the case then try replacing the battery with a new one.

If this doesn't fix the issue then try using a normal flat-head screwdriver to break open the casing of the fob's plastic. Be careful not to damage any internal components, or scratch the plastic. After the battery has been removed and replaced with a brand new one.

After the new battery has been put in, shut and open the doors using the mechanical key (every Kia fob has an emergency mechanical key that can fit into the slot). Test the key fob to confirm it's functioning properly. Contact a dealer, or a locksmith to address the issue when the fob still is not working. Make sure they make you an emergency key that functions for all trunk and door cylinders, to prevent lockouts in the future.