Peugeot 208 Key Replacement

It is best to delegate the replacement of Peugeot keys for 208 to auto locksmiths with the right equipment and expertise. They can design and program keys faster and less expensive than dealerships.

A dead battery for your coin is most likely to blame the reason your key-fob stops locking or unlocking doors. There are other possibilities that the key is malfunctioning.

Dead Coin Battery

A dead coin battery will stop your Peugeot 208 from locking and unlocking, as well as stopping it from starting the engine. In this instance you'll need make use of the alternative method for starting as described in your vehicle's owner's manual.

Another reason why your 208 might not be starting is because the spark plugs are been damaged. The spark plugs ignite the fuel to start the engine. However they have a finite time of life. If they're not used enough to last, they'll eventually fail.

There is a straightforward solution to this problem. The best option is to check the voltage of your car battery using a multimeter. If the voltage falls below 11,5 volts, then it's time to replace it. It is also necessary to clean the battery's contacts if it has corrosion. This can be accomplished by removing the rubber cover from the two terminals of the battery, and then using a wirebrush to remove any corroded parts of the battery. After that, you need to connect the positive pole cables to the negative.

Water Damage

If your 208 won't start and the battery has not been replaced, you must look at the spark plugs. You may find that they are filthy and don't spark. The spark plugs can be cleaned in an workshop.

Peugeot cars use a key with a transponder that is compatible with the immobiliser. This ensures only the correct key can turn the engine. If the chip inside the Peugeot key is damaged, then it won't send the correct signal to the vehicle.

This is a very common issue that can occur due to water damage. This is a frequent issue in warmer climates where the vehicle has been exposed to snow or rain. If this is the case, contact a reputable auto locksmith who will have all of the tools and equipment required to change the key's programming. They'll also have the latest technology and machinery required to make the Peugeot smart key. The process shouldn't take longer than 15 minutes.

Faulty Battery Contacts

Peugeot replaced the old transponder chips with a new model that is based on electronic components that are mounted on a circuit board. This new system works well when it's new, however, over time, the circuit boards begin to degrade and stop working correctly.

This could stop the immobiliser chip from working, so your car won't start. If this is the case it's recommended to get in touch with a Peugeot specialist or locksmith.

A common issue is when the battery of the key fob starts to die. This causes the blade of the key to stop feeding into your lock. A locksmith for cars can replace the battery and cut a fresh blade for you, this is usually a simple fix.

Faulty Receiver Module

If your peugeot 107 key key fob stopped working after dropping it on the floor, getting exposed to a sudden downpour or accidently washing it or washing it, it could be due to a malfunctioning receiver module. The receiver module is responsible for transmitting radio signals to the onboard computer which regulates the central locking system of your Peugeot vehicle.

The key fob itself has rubber seals to prevent water from getting to the chip inside. However prolonged exposure to water can be able to penetrate these seals and cause damage to the chip. The high salt content of the ocean water or pool can cause damage to the key fob when it is submerged.

If your Peugeot spare key fob stops working it is necessary to have the module replaced. This is only completed by an experienced auto locksmith or Peugeot specialist. Peugeot keys unlike other automobiles, are secured by an immobilizer system. This requires the correct coding to start the car. It is for this reason that you should only trust a Peugeot locksmith to create and program an alternative.

Computer on board is not working properly

The computer on board in your peugeot 308 key fob replacement is the one responsible for all of the systems in your car, from power windows to airbags. The on-board computer will display a code if something goes wrong. The code is stored within the system until the issue is fixed. This will often require the on-board computers to be replaced.

One of the most common reasons for the airbag light turning on is loose or corroded connections within the airbag sensor. This could be due to wear and tear, aging or exposure to moisture and salt. It is crucial to get this issue addressed as quickly as you can, as an airbag that is not functioning properly could be risky in the event of an accident.

If you find a card not found error on your Peugeot, the key battery in the key fob might be weak or dead. This will stop the key fob from sending a signal that will disable the immobilizer in your vehicle. You can test this by pressing the unlock button on the key fob, then trying to start your vehicle. If this does not work it is because the battery of the key needs to be replaced.