Peugeot 208 Key Replacement

Peugeot 208 key replacement should be left to auto locksmiths with experience with the right equipment and technical know-how. They can program and create keys faster and less expensive than a dealership.

A dead coin battery is most likely to be at fault the reason why your key fob isn't locking or unlocking doors. There are other reasons that the key could be malfunctioning.

Dead Coin Battery

A dead coin battery will prevent your Peugeot 208 from locking or unlocking, and cannot start the engine. If this is the scenario, you'll need use the backup starting method that is described in the owner's manual of your vehicle.

The spark plugs could also be worn out. Spark plugs are what ignite the fuel to start the engine. They have a limited lifespan. They'll eventually degrade if they're not used enough.

There is an easy solution to this issue. Examine the voltage of your battery with a multimeter. If it's lower than 11.5 Volts it is time to replace it. If the battery has corrosion, it is important to clean its contacts. You can do this by lifting the rubber covers covering the two battery terminals and using a wire brush to remove any corroded components of the battery. Then, you should connect the cables that connect the positive and negative poles.

Water Damage

If your 208 isn't starting and the battery is not running, then make sure whether the spark plugs are working. You might find that they are dirty and they don't spark. This can be easily corrected by cleaning the spark plugs in the workshop.

peugeot 207 key replacement automobiles are equipped with a transponder that is compatible with the immobiliser. This guarantees that only the right key is able to turn the engine. If the chip inside the Peugeot key is damaged, then it won't send the proper signal to the vehicle.

Water damage is a frequent reason for this issue. This is a frequent issue in warmer climates where the vehicle has been exposed to snow or rain. If this is the case, contact a reputable auto locksmith who has all of the tools and equipment needed to change the key's programming. They will also have the most up-to-date technological know-how and machinery required to make a Peugeot 208 smart key. The process shouldn't take longer than 15 minutes.

Contacts to the battery are not working properly.

Peugeot replaced the old transponder chips with a new version that makes use of electronic components that are mounted on a circuit board. The new system is fantastic when it's brand new, but the circuit boards wear out over time and stop working properly.

This could stop the immobiliser from activating so your vehicle won't be able to start. If this happens it's a good idea contact a Peugeot specialist or locksmith.

Another issue that is common is when the battery of the key fob is dying, this causes the key blade to stop feeding into the lock. A car locksmith can replace the battery and cut a new blade for you, it's typically a quick fix.

Faulty Receiver Module

It could be that the receiver module is faulty if your Peugeot key fob doesn't work after being dropped on the floor, or exposed to a stormy rainstorm, or accidentally washed. The receiver module is responsible for transmitting radio frequencies to the onboard computer which regulates the central locking system of your Peugeot vehicle.

The key fob itself has rubber seals to prevent water from getting to the electronic chip inside. Water can damage the chip if it is exposed to the water for an extended period of period of. Submerging the key fob into sea water at the beach or throwing it into the pool can be particularly damaging due to the high salt content.

The module must be replaced if your Peugeot spare key isn't working anymore. This can only by done by an Peugeot specialist or an expert auto locksmith. As opposed to other cars, Peugeot keys are protected by an unique immobilizer system that requires the correct code for the start of the engine. It is for this reason that you should only rely on an authorized Peugeot locksmith to design and program a replacement.

Computer on-board is not working properly

The computer on board in your Peugeot is responsible for a number of the systems within your car, from power windows to the airbags. The on-board computer displays a code if something goes wrong. This code will be saved in the system until the problem is fixed. This will often require the on-board computers to be replaced.

The most common reason for the warning light of the airbag to turn on is corrosion or loose connections within the sensor. This can be caused by wear and tear, ageing or exposure to moisture and salt. This issue needs to be addressed as soon as you can, as an airbag malfunctioning could pose danger in the event in the event of an accident.

If your Peugeot is showing a card that is not being detected error, then the key battery inside the key fob may be dead or weak. This will stop the key fob from sending a signal to deactivate the immobilizer in your vehicle. You can test this by pressing the unlock button on the key fob, then trying to start your car. If it doesn't work then the battery in the key fob has to be replaced.