Reasons Your fiat replacement key 500 Key Fob Won't Work

A fiat ducato replacement key (Www.softjoin.co.kr) 500 key fob makes it simple to open doors and start your car. However, there are numerous reasons why the fob won't be working. This includes a dead battery, water damage, receiver modules issues, and interference.

This listing is for a NEW replacement fiat 500 key fob Fiat Flip Key Remote that is similar to the Ilco brand. It has to be professionally programmed (click here to search for local locksmiths in the automotive industry). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

The most frequent reason why the 500 key fob won't work is the battery is dead. Modern key fobs have a very limited range of operation, and must be within just a few feet of the vehicle to function. If you're far from your vehicle and press the key fob button the car won't respond, and will display the "Key Fob Not Detected" message in the instrument cluster.

If this occurs you need to replace the battery of your coin-cell (Part Number CR2032) by a fresh one of a reputable brand like Panasonic Duracell or Energizer. They are available at your local hardware store or on the internet.

You can test the battery of your coin-cell by pressing the buttons while you're standing close to your Fiat 500. The car will flash its parking lights and the key fob will operate the lock and unlock switches.

If your key fob still does not work after replacing the battery, there could be water damage that prevents it from communicating with the module in your vehicle. Water damage can happen in a variety of ways, from a light splash to submerging the fob into salt water at the beach. If you suspect that your fob has been exposed to water, you can try placing it in a dry rice bag to draw the moisture out. If this doesn't work your fob may need to be reset by a professional locksmith or dealer.

Water Damage

Damage to the water supply can occur if you submerge the fob in the ocean, or wash it in a machine. Saltwater can be particularly harmful to the circuit board of the fob and can cause it to short out and eventually die. It's not the best idea to soak the fob in water however, don't give it up in the event that you accidentally drop it in the water or don't remove it from your pocket.

First, remove the battery. Before replacing the battery, clean the electronic chip using isopropyl or another similar product. Check the fob to see if it is working. If the key doesn't function it could need to be programmed again. This is usually handled by a professional or dealer auto locksmith.

If your key is old and is not programmed for your vehicle, you will need to replace it completely. This is a simple procedure which can be accomplished by a professional locksmith for automotive use. The locksmith will need to cut the key to match the ignition in your vehicle. The locksmith will also need to reprogram your fob into the vehicle's system. This is a low-cost and quick procedure that can be completed the same day.

Receiver Module Issues

The 500 key fob you have may be inoperable because it's out of range. The remote's range is of 30 feet. Therefore, in the event that you are far away from your vehicle it won't respond to your commands. It is possible to solve this issue by moving the remote closer to your vehicle until it responds.

If you've replaced the coin battery (commonly called"button" or "button" or "watch") and your fob doesn't function It could be because of an internal circuit board issue. In most cases, reprogramming the fob will fix the issue. You can find the instructions on how to do this for most vehicles by searching YouTube or checking out the owner's manual.

It is possible to replace the metal clips that hold the coin batteries in the correct position. If they lose tension it can prevent your coin battery from sitting properly and cause your remote to malfunction.

In rare cases the fob can become out of the vehicle's sync because due to hardware or software issues. You can fix this issue by visiting your local auto-locksmith or dealer to reprogram your key fob. In certain instances, the software may also require reinstallation to your body control modules.

Interference

Interference can also cause the key fob not to receive or transmit a signal. This is possible when the key fob is near radio transmitters (cell phones or radar detectors) or any other source of electromagnetic radiation. Other reasons why the key fob might not work include a weak connection to the buttons or damage to the internal chip or water damage.

If your key fob suddenly stopped working, or you've tried everything at home to solve the issue (e.g. You might have a damaged 500 receiver module If you've tried replacing it with a battery, reprogramming, or using a spare key fob. The receiver module, which is located under the dashboard, receives radio frequency signals from your key fob. It converts the signals into electronic commands, which are then translated by the vehicle.

Luckily, there is an easy method of resetting all on-board systems in your 500 keys, including the key fob. Disconnect the 12 volt battery for about 15 minutes by taking off the negative cable first then the positive cable. Then, reconnect the battery. This will clear out any residual electricity and restart the car's computer system, which could allow you to get your key fob working again. If the problem persists you should speak with a certified technician. They'll be able to diagnose the exact cause of your problem.