Fiat 500 Replacement Key Fob

If your remote key fob isn't working, it's time to replace the battery. If you replace the battery, but it isn't working, the problem may be elsewhere.

At United Locksmith, we specialize in the creation of new keys for old automobiles. We have the tools and components required for this service.

Dead Coin Battery

A dead battery is the most frequent cause of your Fiat 500 keyfob not locking or unlocking the doors. The battery for the coin cell in the key fob will deplete quickly if you don't use frequently enough. If your remote started to show signs of weakness such as a loss of range and stopped working completely The battery is probably dead.

The battery in the key fob is secured by metal clips that hold it in place. If the clips are not secure, they could cause contact issues that prevent your remote from receiving power. Use a flathead screwdriver to open the retaining clips and then remove the old battery. Use a battery that has the same size, voltage and specification as the original.

The key fob could be damaged or corroded by exposure to water. Even a quick bath in warm, soapy water can cause damage to the chip. It is best to keep your key fob in a dry environment.

Water Damage

Damage to your water supply could be the reason for your key fob's inability to function properly. The rubber seals on key fobs stop them from being damaged by a light drizzle or splash of water. However, it's important to keep the car keys away from the ocean, washing machine, and the pool.

The key fob is equipped with an electronic chip that sends an alert to the immobilizer of your car. The chip allows the 500 to lock and start. If it gets wet it will cease to function.

If you're trying to determine if your key fob is still functioning it is possible to clean the internal electronics with isopropyl or an electronic cleaner. It is best to replace the key fob if it is submerged in salt water rather than try to fix it yourself.

A replacement fob can cost you a bit but it's far less expensive than paying to have your Fiat 500 towed to a dealer and repaired there! You can also fix it yourself by following just a few steps. Just make sure you have the correct battery type before you attempt to open your key fob. This is a job that's more straightforward than it appears, and you can find step-by-step directions online for nearly every key fob for your car.

Faulty Chip

The chip inside the key fob communicates with the immobiliser of your car to ensure that your vehicle will only start when correct keys are inserted. If the chip is damaged or destroyed the car won't start no matter what you do.

Water damage or a dead battery are the most frequent causes of a faulty chip. It is best to leave the repair to a professional locksmith who can repair the chip quickly and at an affordable price.

If your key fob will not function after exposure to water that is clean from the tap or rain then remove the battery. Clean the electronic component using paper towels. If the key fob still doesn't work it's most likely an issue with the chip and will need to be replaced.

Some people will go to their dealer when in need of a new fiat key - continue reading this.., fob, but this could be a costly alternative. If you are looking for a cost-effective way to get your Fiat key fob repaired then look no further than United Locksmith. We have the equipment and know-how to fix your Fiat fob quickly and professionally. way.

Faulty Receiver Module

Fiat key fobs transmit a signal up 50 feet to the vehicle, which will open and lock the doors (and start the vehicle if it has automatic transmissions). There are many reasons why the fob might stop working. It could be due to a dead battery water damage buttons, worn ones as well as a receiver module problem and signal interference, or an electronic chip that has failed.

If the fob has been placed in a pocket that experienced extreme trauma, such as being dropped on a hard floor or being washed in a wash machine, it may not be able to communicate with the car's Body Control Module (BCM). The BCM is a security device which will only accept signals from genuine original keys.

If this is the case, then you have to replace your fob. A professional locksmith will take care of the entire replacement process including programming a new key for your 500. In fact, they can offer you a clone key that works just like the original fob (and costs less than the cost).