Reasons Your Fiat 500 Key Fob Won't Work

A key fob from fiat 500 key replacement cost (mouse click the following website page) 500 is a great way to open the doors and start the car. However, there are a variety of reasons why the fob won't be functioning. These include a dead coin battery water damage, receiver module problems, and interference.

This listing is for an NEW replacement Fiat Flip Key Remote - similar to the Ilco brand that needs to be programmed professionally by a local automotive locksmith (click here for Locksmith Search). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the most common cause of your 500 key fob being inoperative. Modern key fobs have a very limited operating range and should be within some feet of the vehicle in order to function. If you're far from your vehicle when you press the key fob button the car won't respond and will display a "Key Fob Not Detected" message in the instrument cluster.

If this happens you need to replace the battery of your coin-cell (Part Number CR2032) with a new battery of a trusted brand like Panasonic Duracell or Energizer. They are usually available in your local hardware store or online.

You can test the battery on your coin-cell by pressing the buttons while standing near your fiat 500 replacement key 500. The car should blink its parking lights and the key fob should operate the lock and unlock buttons.

If the key fob doesn't work after replacing the battery, it may be damaged by water, which prevents it from connecting to the receiver module inside your vehicle. Water damage can occur in many ways, such as an easy splash or submerging your key fob in saltwater at the beach. If you suspect that your fob was exposed to water, place it in a bag of rice to draw out the moisture. If this does not work, you'll need to have your fob reset by an auto locksmith or a dealer.

Water Damage

Water damage can happen if you immerse the fob into the ocean or wash it in a machine. Saltwater poses a particular risk to the circuit board of the fob which causes it to short out and eventually die. In the event that you let your fob get wet, it's not an ideal idea but if you accidentally drop it in the water in a cup or don't remember to take it out of your pocket before you run the washer Don't give up hope.

First take the battery off the fob. Clean the electronic chip with isopropyl or a similar product and then dry it completely before replacing the battery. Next test the fob to verify if it is working. If the key isn't working, it may need to be reset. This is usually done by a professional or dealer auto locksmith.

If the key is more recent and hasn't been programmed to your vehicle, it will likely need to be replaced completely. This is a simple process that can be handled by a professional locksmith for automotive use. The locksmith must cut the key to match the ignition on your vehicle. The locksmith also needs to reprogram your fob in the car's system. It's a simple and cost-effective process that can usually be completed within the same day.

Receiver Module Issues

Your 500 key fob might stop working because it is out of range. The remote has a range of 30 feet. Therefore, should you be too far away from your vehicle it won't be able to respond to your commands. It's easy to remedy this by moving your remote closer to your car until it responds.

If your fob doesn't work after you replace the coin battery, also known as a "button", "watch" or "button", it could be due to an issue with the circuit board inside. Reprogramming your fob can resolve the issue. You can find directions on how to do this for all vehicles by searching YouTube or checking out the owner's manual.

You may need to replace the metal retaining clips that keep the battery of your coin in place. If they lose tension, it could prevent your coin battery from sitting properly and cause your remote to malfunction.

In rare instances, the fob can become out of sync with your vehicle because of hardware or software issues. This could be a huge trouble, but you could frequently fix this issue by visiting a local dealer or auto locksmith to have them reprogram your fob for you. In some cases they may have to install the software again in your body control module, as well.

Interference

In addition to a dead coin battery The key fob might not be receiving or transmitting signals due to interference. This can happen when the key fob is close to an electronic radio transmitter (cell phones or radar detectors) or any other source of electromagnetic radiation. The key fob may not work because of a weak connection to the buttons water damage or damage to the internal chips.

If your key fob suddenly stopped working, or if you have tried everything at home to resolve it (e.g. You might have a damaged 500 receiver module in the event that you've tried replacing the battery, reprogramming, and using a spare key fob. The receiver module is located under the dash and receives the radio frequency signals from the key fob. Then, it converts them into electronic commands that the vehicle interprets.

Luckily, there is an easy method of resetting every single system on board in your 500 device, including the key fob. Disconnect the battery for 15 minutes by removing first the negative cable and then the positive cable. Reconnect the battery. This will eliminate any remaining electricity and restart the car's computers, which could allow you to get your key fob working again. If the problem persists you should seek out an expert technician. They will be able to identify the exact cause of any problems.