How to Replace a Kia Sportage Replacement Key

The key in many Kia models has a keyless entry system built in. This key usually resembles an remote control, and can be changed with a fresh one from an kia replacement key fob dealer or locksmith.

Key fobs can stop working due to a number of reasons, such as a dead battery, worn-out buttons signals, signal interference or water damage. Here are some suggestions on how you can get your Kia Sportage replacement key back to working.

How do you replace the remote key or smart key?

It doesn't matter if your Kia is equipped with an intelligent key, remote key, push to start key or a regular non-transponder steel key the battery in these keys will eventually require replacing. This is particularly relevant if your car displays a message that the smart or remote key is not powered by the battery.

This is a relatively easy process. In order to replace the key fob battery, remove the mechanical key from the slit on the back of the key fob. You then need to remove the cover. Inside the key fob, there will be the small screw that holds the battery in its place. Take out the old battery by removing the screw with a small screwdriver. Then, insert the new one and close the slit in the key fob.

Test the key fob by pressing the lock and unlock buttons. You're good to go in case the doors lock and unlock as expected. You can now take advantage of your Kia's hands-free lock/unlock feature whenever your fingers get chilly or you need to go on errands around Brandon.

Not all key fobs may need to be programmed (transponder chips or smart keys). This requires a special programming machine that only the dealer or automotive locksmith has access to. Other keys (non transponder metal keys) are not required for programming. If you want to change the programming of your key, you'll have to record the key code number on the key code tag.

How do you replace the battery?

If your Kia key fob isn't responding to pressing the lock or unlock button on the fob, it is a sign that the battery needs to be replaced. A battery that is not functioning properly could cause other problems like the check engine light turning on or delayed engine cranking. Fortunately, replacing the key fob battery is a relatively simple DIY project that requires only the most basic tools.

Before beginning the process ensure that your vehicle is off and that all doors are closed. Find the small, metal or plastic piece on the bottom of your key fob, and move it until a metal key is released. This key can be placed inside the driver door handle to unlock your car.

To replace the battery on the key fob, remove the cover on the rear. Use a pry tool to open the latch that holds the black negative cable. Remove the old battery and orient the new battery to ensure that the "+" positive side is facing your face and the "-" negative side is facing the fob's electrical contacts made of metal. Push the new CR2032 battery straight into position with care to avoid using too much force to avoid bending or damaging the metal contacts.

After you have installed the new battery then turn the key fob off and on in the ignition until the door locks up. You can then test your Kia's key fob again to make sure it's working properly.

How to replace the smart key

You could have a standard keyfob, or a Smart Key based on the model of Kia Sportage. The difference between the two is that the smart key has tiny mechanical key blade in it, whereas the standard fob isn't equipped with. Both key fobs are equipped with batteries that will eventually require replacing. It is a simple process that takes less than two minutes.

Be sure to switch off your Kia and sit on a flat and well-lit surface prior to you begin. Be aware that the fob can contain tiny parts that could fall should you not be careful.

The small release button is located on the lower backside. It can be an oval silver button or a rectangular slot. You can open the key fob by pressing the button.

Once the key fob is opened, remove the battery that was in it. The new battery is a CR-2032, and can be purchased on the internet or at your local auto parts store. After you're done, your key fob should allow you to lock, unlock, and start your vehicle, even if it isn't running.

How do you replace the mechanical key?

The kia key replacement keyfob is a great convenience that allows us to lock or unlock our car by pressing one button. Like any other device it may have issues from time to time. There are solutions to solve these issues and keep your key fobs running for a long time.

One of the most frequent problems is a low or dead battery. This could cause your device to stop working or operate intermittently. If this is the case it is time to replace the battery a new one.

If this isn't enough to resolve the issue then try using a normal flathead screwdriver to wedge open the fob's plastic casing. Be careful not to damage internal components, or scratch the plastic. After the battery has been removed, replace it with a brand new battery.

After the new battery has been put in, close and then open the doors using the mechanical key (every key fob in the kia has an emergency mechanical key that will fit in the slot). Test the fob to make sure it's working properly. Contact a dealer, or a locksmith to solve the issue in the event that the fob is not working. To avoid locking outs in the future, ensure you purchase an emergency key that can be able to work with all door and trunk cylinders.