How to Replace a Kia Sportage Replacement Key

The key in many Kia models comes with an entry system that is keyless in. The key functions like an remote control, and can be exchanged with a Kia dealer.

Key fobs may stop working due to various reasons, such as a dead coin battery, worn buttons, water damage, signal interference and a malfunctioning receiver module. Here are some tips on how to get your Kia Sportage replacement key to function again.

How do you replace the remote key or smartkey?

If your Kia is equipped with an intelligent key, remote key, push-to-start keys, or a regular non-transponder metal key, the battery in these keys will eventually need replacing. This is especially relevant if your vehicle displays a message telling you that the remote or smart keys aren't powered.

It's an easy procedure. To replace the keyfob battery, remove your mechanical key from the slit that is located at the back of the fob. Then, you need to pry the cover open. A small screw will be found inside the key fob that holds the battery in the correct position. Remove the old battery by unwinding the screw using a small screwdriver. Then insert the new one and close the slit inside the key fob.

Test the key fob by pressing the lock and unlock buttons. You're good to go if the doors lock and unlock as you expect. You can now use your kia ceed replacement key's hands-free lock/unlock feature when your fingers are cold or you need to run some errands in Brandon.

Note: Some key fobs might need to be programmed (transponder chips or smart keys). This requires a specific programming machine that only the dealer or locksmith can access. Other keys (non-transponder metal keys) do not require programming. If your key requires to be programmed, you must be aware of the number that is stamped on the key code tag and keep it in a secure location.

How do you replace a battery?

If your Kia key fob is not responding when you press the lock or unlock button on the fob, this is a good indicator that the battery needs to be replaced. A low battery could cause other issues like the check engine light coming on or delayed cranking of the engine. Fortunately replacing the battery on the key fob is a simple DIY task that requires only a few basic tools.

Before you begin before beginning the process, ensure that your vehicle is off and that all doors are closed. Locate the small plastic piece that is on the bottom of your key fob, and play with it until a metallic key slips out. The key can be put into the driver door handle to unlock your car.

To replace the key fob battery, remove the rear cover and use a plastic bar tool to remove the latch holding the black negative battery cable. Remove the old battery and then orient the replacement battery to ensure its "+" side is facing you and the "-", negative side is facing the fob's electrical contacts. Avoid using too much force when pushing the new CR2032 into place to avoid breaking or bending the steel contacts.

After installing the new battery, turn the key fob on and off in the ignition until the door locks cycle. Then, you can test your Kia key fob to check whether it's working again.

How do I replace a smart key

You may have either the standard keyfob or Smart Key, based on the model of Kia Sportage. The smart key has an embedded mechanical key blade while the standard keyfob does not. Both key fobs have an internal battery that will eventually require changing. This is a simple procedure which takes just two minutes.

Before you get started before you begin, ensure that you are on a flat surface with sufficient lighting and that your kia ceed key fob is turned off. Be aware that the fob has tiny pieces that could be thrown off if you're not careful.

The small release button is located on the lower backside. It's either a circular button or rectangular slot. You can open the key fob by pressing the button.

After the key fob has been open, remove the battery. The new battery is a CR-2032, and can be bought through the internet or at a local auto parts shop. After you've finished with the battery, you should be able to lock or unlock your vehicle with your key fob - even if the engine isn't running!

How to replace a mechanical key

The Kia keyfob is an excellent convenience that lets us lock or unlock our car with just pressing a button. Like any device like a key fob, the Kia can occasionally have problems. Luckily, there are steps to take to resolve these issues and ensure that our key fobs are in good working order for the long run.

One of the most common problems is a weak or dead battery. This can cause the device to cease working or even to stop working intermittently. If this happens then try replacing the battery with a new one.

If this isn't enough to resolve the issue you can try using a standard flathead screwdriver and wedge it into the casing of the fob's plastic. Be cautious not to damage any internal components or scratch the plastic. After the battery has been removed then replace it with a brand new battery.

Close and open the door using the mechanical key. (Every Kia fob comes with an emergency mechanical key which will fit into the slot). Test the fob to make sure it's functioning properly. If the fob isn't working, call an expert locksmith or dealer to help resolve the problem. Make sure they make you an emergency key that can work for all trunk and door cylinders, to avoid future lockouts.