Peugeot 3008 Key Fob Problems

Peugeot's 3008 SUV is a mid-sized model with a lot of positives. It's stylish, it drives well and comes with a large boot. But is it able to beat off strong competition in the most crowded segment of the market?

If your Peugeot key fob is not functioning, it may have been exposed to clean tap water or soapy water. It is possible to take off the battery and clean it using electronic cleaner or isopropyl alcohol.

Dead coin battery

Peugeot key fobs include a small coin battery that powers their remote locking and other features. The battery has a short life span and may get worn out after years of use. The test of voltage is a quick method to determine if a battery is not working properly. Multimeters are used to measure voltage between the poles that are plus and minus of the battery. This test will determine whether the battery is dead.

The receiver module may be the reason behind your key fobs not working after using your peugeot 207 key 3008 for a prolonged period. The receiver module is responsible for receiving radio frequency signals from the key fobs, and then sending signals to the car's systems. If the receiver module is in a fault, it won't be able to send commands to other modules inside the car.

Sweat or moisture on the circuit board is another common reason for an inoperable key fob. It can trigger short circuits, which will drain the battery and stop the remote locking feature of the fob. If this happens then you must bring your key fob into a chip level service technician to repair it.

Water damage

Whether you dropped your key fob into the pool, threw it in the washer or just left it in the rain for too long, water damage can cause a lot of problems. Water is a good conductor and can cut off circuit boards. It can also cause corrosion to the metal lines on the key fob as well as other components. A circuit board that is wet could also cause the battery dump its charge.

If you have an extra key fob try using it to lock/unlock your Peugeot 3008 to rule out the possibility that a dead battery is at the root of the problem. Another issue that can stop your key fob from working correctly is interference signals that interfere with the signal that is sent to the receiver module. These signals can come from a variety of things including radio transmitters that are near.

If you hear sloshing sounds emanating from your Peugeot 3008 when driving, it's most likely because of a blocked condensate evaporator drain. You can test this by blowing compressed air through the drain holes in your door. You can also use flexible metal wire to wiggle drain holes to remove any dirt that has collected. The sloshing sounds can be a sign that there are air pockets in the coolant system.

A malfunctioning receiver module

The receiver module of the Peugeot 3008 key fob is responsible for sending the remote keyless system signal from the key fob to the car's receiver. If this module is damaged, it can stop the car from recognizing the key fob. Other causes of this problem include the battery being dead or water damage, as well as interference with electronic devices that operate at the same frequency as the key fob. In these instances an error message such as "card not detected" could appear on the display.

There are a variety of options to solve this issue. You can try replacing the battery, or reprogramming the key fob. You can also start your car with a spare. However, if your key fob isn't working even after these steps, it could have a chip that's not working properly.

It is best to remove the chip and clean it with rubbing alcohol and paper towel. If the chip is damaged you must purchase an entirely new one. The FB Series enclosures come with an holder for coin cells that is compatible with the most popular types of key fob batteries. The enclosures can be personalized with digital printing and CNC-machined cutouts. If your key fob has been exposed to dirty or salty tap water, the chip may be contaminated and requires to be cleaned.

Faulty keyless entry systems

If you see "card not detected" This means that your car is unable to receive the signal from your key fob. This could be due to a number of reasons, such as the battery being weak or dead. Often, the problem can be fixed by pressing the start button with the key fob. In certain cases, you might require taking the keyfob to an Peugeot dealer for further repairs.

Checking the battery is the first step in solving the issue with a Peugeot 3008 keyfob that won't unlock or lock doors. Batteries are the most common reason for a fob that is malfunctioning however, there are other causes that can cause this issue too. This includes worn buttons and water damage.

If your Peugeot key fob has been exposed to clean tapwater, it's a good idea to take the battery off. Then, dry the electronic components using paper towel. You can also use isopropyl alcohol or cleaning solution to do this. If the fob has been exposed to soap or salty water, it's best to replace it.

If your key fob still not working, try to reset it by disconnecting the battery with 12 volts for approximately 15 minutes. Then connect the negative cable first, followed by the positive one.