Reasons Why Your Nissan Qashqai Key Fob Won't Work

The Qashqai's bigger dimensions give it a distinct SUV feel. Its 19-inch alloy wheels in Ti and STL versions may also be firm. Its front tyres can also lose grip on rough surfaces and its CVT could occasionally exhibit wrist-flexing torque steer.

This is usually caused by a dead battery, which can be replaced in just a few minutes. Make sure that the replacement battery is of the same size, voltage and specifications.

Water Damage

One of the most frequent reasons a Nissan key fob gives the "key ID is incorrect" message is due to water damage. The key fob has rubber seals that protect the electronic chip inside, but prolonged exposure to moisture can cause it to stop functioning properly. This is typically the situation when you drop your key fob into the ocean or a swimming water pool, but it could happen when it's wet due to soapy hands or rain.

If your key fob is exposed to water for a lengthy time, it may need to be cleaned with isopropyl ethanol or electronic cleaner. It may also need to be taken to an expert for repair or replacement.

If your key fob need to be replaced the process is simple. Make sure you've got the correct multipack (CR2032 3V). Open the back and front cases using the help of a small screwdriver. You'll have to remove the retaining clips made of metal and then push out the old battery, then insert the new one. After reassembling the fob put the mechanical key back in its place and make sure it works as expected. If it isn't it is necessary to take it to your local Nissan dealer or a professional auto locksmith to repair the key chip. Fortunately the chip isn't usually damaged by water exposure and this shouldn't be a major expense.

Dead Coin Battery

The coin battery is a second common reason that your Nissan Qashqai remote key fob may not work. These batteries last for three to five years, but can become faulty over time in the event that the fob has been frequentedly dropped. You can try replacing the battery with a fresh one, but make sure it's the same voltage and size as the original. If you choose to use a brand new battery, it could cause the key to be assigned an incorrect key ID. This will stop it from being paired with your vehicle.

The most efficient method to change the battery inside a Nissan Qashqai Key Fob is to pry it open with an small screwdriver that has a flat head. The screwdriver needs to be inserted into a small notch at the bottom of the key fob. Gently twist the screwdriver to separate the two halves. Then, take out the old CR2025 button cell battery and replace it with another one after confirming its position on the fob.

Before putting the new battery in check to ensure there is no dirt or water damage on the terminals. If this is the case, clean the terminals using some isopropyl ethanol. Also, ensure that the pole cables are connected properly - they must be connected to the negative and positive poles of your battery, respectively.

Diagnostics of a fault

If your nissan key replacement near me Qashqai key fob stops working after exposure to clean tap water or rain, it may be an indication of an internal chip problem. You'll need a new keyfob if you are unable to fix the issue by changing the battery. If the key fob didn't work after dropping it, it's likely that the chip inside was damaged. You can usually get the key fob back to work again if you remove and clean the chip with alcohol and paper towels and then insert it back into.

One common error you may see on the dashboard of your car is "Key ID Not Correct." This means that the car is unable to recognize the key fob, and will not allow it to start the engine. This issue can be caused by several ways, such as water damage, malfunctions that are not detectable within the key fob circuitry or RFID interference.

If the 12 volt battery in your key fob broken or is not supplying sufficient electric current it will cease to function. This can affect the Nissan Qashqai's remote keyless system, central locking and the ability to start the engine using the key fob. Check the batteries inside the key fob in case you are not able to lock and unlock your door manually. You can also try re-inserting the battery to reset the transmitter.

Reprogramming

If the key fob was not submerged in saltwater it should be able to be restored to its original state with a simple rinse of clean water. You can also clean the electronic chip using isopropyl or electronic cleaner. If none of these works it is possible to replace the key fob.

If your Nissan Intelligent Key is still not working, it could be a problem with the connection between it and your car. Start by turning the ignition key without beginning the car. Continue to do this until the hazard light flashes two times. Then, turn off the car and take out the key.

Open the fob compartment of your vehicle. It's usually located on a door jamb or driver's door handle. Find the button that says "program" and press it. You will hear a chime once the process is complete.

Now that your Intelligent Key is relinked to the car, it's time to test it out. Click all the buttons on the key while at a distance away from the car. If the lights flash and the horn sound it means that the key has successfully linked to the Nissan. You can also test it near the Nissan.