Fiat 500 Replacement Key Fob

It may be time to replace the battery if the 500 remote key fob is not working. If you replace the battery and it still doesn't work the issue could be elsewhere.

At United Locksmith, we specialize in the creation of new keys for old automobiles. We have all the tools and accessories needed to provide this service.

Dead Coin Battery

The most common reason why your fiat 500 replacement key fob 500 key fob will not unlock or lock the doors is due to a dead battery. The coin cell battery in the key fob can be depleted quickly when you don't utilize it often enough. If your remote is beginning to show signs like a loss of range or stopped functioning and the battery is not working, it could be dead.

Metal clips hold the battery securely within the key fob. If the clips are not tight, they can cause contact issues that prevent your remote to receive power. Use a flathead screwdriver break open the retaining clip and remove the battery. Use a battery that has the same size, voltage and specification as the original.

The key fob could also become corroded or damaged through exposure to water. Even a short bath in warm, soapy water could damage the chip. It is recommended to keep your key fob in a dry area.

Water Damage

If your key fob isn't working correctly, it could be caused by water damage. Key fobs have rubber seals to protect them from being damaged by rain or a splash of water. However, it is very important to keep your car keys from being tossed into the pool, ocean and washing machine!

The key fob contains an electronic chip inside that sends a signal to your car's immobilizer system. This is what allows your 500 to start or lock, but in the event that the chip becomes wet, it's unable to longer function.

If you want to check whether your key fob functional You can clean the internal electronics using isopropyl or an electronic cleaner. However, it's better to purchase a replacement from a dealer rather than trying to repair the key fob which was submerged in salt water.

A replacement fob may cost you some money however it's much cheaper than having to have your Fiat 500 towed to a dealership and fixed there! In addition, you can do it yourself with a few easy steps. Just ensure you have the correct battery type before you attempt to open your key fob. You can find step-by-step instructions for any car keyfob on the internet.

Faulty Chip

The chip inside the key fob communicates with the car's immobiliser unit to make sure the vehicle is only capable of starting when the correct key is used. If the chip is damaged, or corrupted in any way your car will not start.

Water damage or a dead cell battery are the most common reasons for a faulty chip. It is recommended to leave the repair to a professional locksmith who can repair the chip in a short time and at a an affordable cost.

If your key fob stops working after exposure to clean tap water or rain, remove the battery and clean the electronic component using a paper towel to ensure that it is completely dry before putting it back into. If the key fob does not work, there's an opportunity that it is malfunctioning components and need to be replaced.

A few people will visit their dealer if they need a new Fiat fob. However, this could be expensive. If you are looking for a low-cost solution to have your Fiat key fob repaired, look no further than United Locksmith. We have the tools and experience needed to fix your Fiat fob quickly and professionally. way.

Faulty Receiver Module

fiat key replacement key fobs send an electronic signal to the vehicle that will unlock and close doors (and start the car for vehicles with an automatic transmission) up to 50 feet. There are a variety of reasons why the fob might not function. These include a dead coin battery damaged by water, worn buttons as well as a receiver module problem or signal interference, or an electronic chip that is malfunctioning.

If the fob was located in a pocket which has suffered extreme trauma (such as being dropped on the floor, or washed in the washing machine) the fob may not be able to communicate with the Body Control Module (BCM) of the car. The BCM is a security device that only accepts signals from genuine original keys.

You'll have to replace the fob if this occurs. A professional locksmith is able to handle all aspects of the key replacement procedure as well as programming a new one for your 500. They can even offer an identical fob that functions exactly the same way as the original (and costs only one-third of what it would cost).