Peugeot 208 Key Replacement

Peugeot 208 key replacement should be left to professional auto locksmiths who have the appropriate equipment and know-how. They can make and program new keys much quicker than a dealership and at a lesser cost.

A dead battery for your coin is most likely to blame when your key fob stops locking or unlocking doors. However, there are other reasons the key could be malfunctioning.

Dead Coin Battery

A dead coin battery will stop your Peugeot 208 from locking and unlocking, and also preventing it from starting the engine. In this instance you'll need make use of the alternative method for starting as described in your vehicle's owner's manual.

Another reason why your 208 might not be starting is that the spark plugs have worn down. The spark plugs ignite the fuel to start the engine. They have a limited life span. They will eventually break down if they aren't used frequently enough.

There is a straightforward solution to this problem. The best way to solve this issue is to check the voltage of your car battery using a multimeter. If it's lower than 11.5 Volts and you are not satisfied, then it is time to replace it. It is also essential to clean the contacts of the battery in the event that it is damaged by corrosion. You can do this by lifting the rubber covers covering the two terminals of the battery and using wire brushes to clean any corroded parts of the battery. Then, reconnect the positive and negative pole cables.

Water Damage

If your 208 won't start and the battery hasn't fallen flat, it is time to examine the spark plugs. You might find that they are simply too filthy and don't spark. The spark plugs can be cleaned in a workshop.

Peugeot cars are equipped with transponder keys that is compatible with the car's immobiliser system. This ensures that only the correct key can turn the engine. If the chip inside the Peugeot key is damaged, it will not send the proper signal to the vehicle.

This is a common problem that can be caused by water damage. This is a common problem in warmer climates where the vehicle has been exposed to snow or rain. If this is the case, contact a reputable auto locksmith who will have all of the tools and equipment required to modify the new key. They also have the latest technological know-how and the equipment required to make a Peugeot 208 smart key. The process shouldn't last more than 15 minutes.

Contacts with the battery may be damaged.

Peugeot changed from the old carbon-encased transponder chips and introduced a new type of chip that uses electronic components on a circuit board. This new system works great when it's brand new, but as time passes, the circuit boards begin to lose their effectiveness and cease working properly.

This can stop the immobiliser chip from activating and causing your car to not start. Contact an peugeot 107 key specialist or a locksmith if this is the case.

A common issue occurs when the battery inside the key fob begins to fail. This causes the blade of the key to stop feeding into your lock. A car locksmith will replace the battery and then cut a new key blade for you. This is a simple fix.

Faulty Receiver Module

It could be that the receiver module is defective if your Peugeot key fob isn't working after being dropped on the floor, or exposed to a sudden downpour or accidentally washed. The receiver module is responsible for transmitting radio frequency to the onboard computer which controls the central locking system of your Peugeot vehicle.

The key fob itself has rubber seals which prevent water from reaching the chip inside. However, prolonged exposure to water can break through these seals, causing damage to the chip. The high salt content in the ocean water or pool can cause damage to the key fob when it is submerged.

The module will have to be replaced if your Peugeot spare key is no longer working. This can only be done by an Peugeot specialist or a professional auto locksmith. As opposed to other cars, Peugeot keys are protected by an immobilizer that is unique and requires the correct code for the start of the engine. This is why you must trust an experienced Peugeot locksmith with the task of programming and creating an appropriate replacement.

Faulty on-Board computer

The on-board computer of your Peugeot is responsible for a variety of features in your car, including airbags and power windows. The on-board computer will show an error code when something goes wrong. This code will be stored in the system until the issue is fixed. This can often mean that the on-board computers to be replaced.

One of the most common causes of the light coming on is loose or corroded connectors in the airbag sensor. This can be caused by wear and tear, ageing, or exposure to salt and moisture. It is crucial to get this issue addressed as quickly as you can, since an airbag that is not functioning properly could be dangerous in the event an accident.

If your Peugeot is showing a card not detected error then the key battery inside the key fob could be dead or weak. This will prevent the key fob from sending a signal to disable your vehicle's immobilizer. You can test this by pressing the unlock button on the key fob and then attempting to start your car. If this fails, the key battery needs to be replaced.