Peugeot 208 Key Replacement

It is better to leave the replacement of Peugeot keys 208 to auto locksmiths equipped with the right equipment and know-how. They can design and program keys quicker and more efficiently than dealers.

A dead battery for your coin is the most likely cause if your key fob stops locking or unlocking doors. There are also other reasons why the key may be malfunctioning.

Dead Coin Battery

A dead battery in the coin compartment will hinder your Peugeot 208 from locking or unlocking, and won't start the engine. In this case, you will need to make use of the alternative method for starting found in your vehicle's owner's manual.

Another reason your 208 might not be starting is that the spark plugs are been damaged. The spark plugs ignite fuel to start the engine. However, they have a limited lifespan. If they're not used enough and they fail, they'll eventually die.

There is an easy solution to this problem. The best option is to determine the voltage of your car battery with a multimeter. If it is below 11.5 Volts it is time to replace it. It is also essential to clean the contacts of the battery in the event that it is damaged by corrosion. This can be accomplished by removing the rubber covers off the two terminals of the battery, and then using a wirebrush to remove any corroded parts of the battery. Then, reconnect the positive and negative pole cables.

Water Damage

If your 208 doesn't start and the battery is not flat then you should check whether the spark plugs are working. You might find that they're dirty and don't spark. The spark plugs can be cleaned in an workshop.

Peugeot cars are equipped with a key with a transponder that is compatible with the immobiliser. This ensures that only a valid key is able to turn the engine. If the chip inside the Peugeot key is damaged, it will not transmit the correct signal to the vehicle.

This is a frequent issue that is often caused by water damage. This is a common problem in colder climates where the vehicle is exposed to snow or rain. If this is the case, you should seek out a reputable auto locksmith who has all of the equipment and tools needed to change the key's programming. They will also have the latest technological know-how and the equipment required to create the Peugeot 208 smart key. The process shouldn't take more than 15 minutes.

Contacts with the battery may be damaged.

Peugeot changed from the old carbon encased transponder chips to a new type of chip that relies on electronic components on a circuit board. The new system is excellent when it's new, however the circuit boards begin to degrade with time and stop working properly.

This could prevent the immobiliser chip from triggering, so your car won't start. If this happens, it's a good idea call a Peugeot specialist or locksmith.

A common problem is when the battery inside the key fob begins to die. This causes the blade of the key to stop feeding into the lock. A locksmith from your car will replace the battery, and cut a new blade for you. This is a quick solution.

Faulty Receiver Module

If your Peugeot key fob has stopped working after dropping it on the floor, being exposed to a sudden rain or accidently washing it may be due to a defective receiver module. The receiver module is responsible for transmitting radio frequency to the onboard computer which regulates the central locking system of your Peugeot vehicle.

The key fob itself has rubber seals that prevent water from reaching the electronic chip inside. Water can damage the chip when it is exposed to the water for an extended period of period of. The high salt content in the pool or ocean waters can cause damage to the key fob, especially if it is submerged.

The module will need to be replaced if your Peugeot spare key is no longer working. This is only done by a Peugeot specialist or a professional auto locksmith. Like other automobiles, Peugeot keys are protected by an immobilizer that is unique and requires the correct code to start the engine. This is the reason that you should only trust an authorized Peugeot locksmith to design and program the replacement.

Computer on-board is not working properly

The on-board computer of your peugeot key fob replacement is responsible for a variety of systems inside your car, including airbags and power windows. The on-board computer displays the code when something goes wrong. This code is saved in the system and remains there until the problem has been resolved. Often, this will involve the on-board computer being replaced.

The most common reason for the warning light of the airbag to flash is corrosion or loose connections within the sensor. This can be caused by wear and tear, aging or exposure to moisture and salt. It is imperative to have this issue addressed as soon as you can, as an airbag that is not functioning properly could be dangerous in the event of an accident.

If your Peugeot is showing a card that is not being detected error, then the key battery in the key fob could be dead or weak. This could prevent the key fob from sending a signal that disables your vehicle's immobilizer. You can test this by pressing the unlock button on the key fob and then trying to start your vehicle. If this doesn't work then the battery in the key needs to be replaced.