How to Replace the Replacement Key Battery For the Saab 9-3

Saab owners have to follow a series of steps that are unique to add an additional ignition key. It requires dealer assistance using the handheld computer known as Tech-2. Then the transponder must be replaced and a key need to be purchased.

Rotate your keys to stop one from wearing out quicker than the other. This will also help keep your keys in top condition.

Replacement Case

Contrary to the classic Saab keys of the past keys, the new keys have electronic components that make it difficult to duplicate. This has made car theft significantly more difficult than 20 years ago. It also makes it more costly to replace keys that were lost.

Every owner of a 9-3 Saab should have at a minimum two functioning keys. If one gets lost, it costs a lot to get another one for the vehicle because it requires replacing the CIM module and programming the locking cylinders. Dealers charge between $100-$200 to do this.

There are ways to reduce these costs. Some parts providers will look up the code from an extra key (usually the same one that opens the doors and turns on the ignition) and cut a new metal key blade for less than the dealer's cost. The key must, however, be identical to the original one in order to function within your car.

Follow these steps to replace the case. You will need a flathead screwdriver as well as some patience. Using the screwdriver, slowly pull the plastic apart and remove the emergency key from the case. Once you have the case open, remove the electronic components and place them inside the new case. Put the correct key and badge inside the case.

Replacement Battery

The Saab 9-3 replacement battery is a budget part that can be quickly and easily replaced. This YouTube tutorial for DIY Cyclone Cyd will show you how to replace the battery for the remote key fob in just four steps. This tutorial will work with any modern Saab key fob. However, the procedure could differ slightly.

The button is normally located just below the Saab logo on the back of the fob. It's usually near the Saab logo on the back of the fob. Use a flathead screwdriver to insert the screwdriver through the small hole in this button. This should be enough to open the fob's case to allow you to replace the battery.

After the new battery CR1632 is in place then you can reassemble your remote key fob and program it to your car. The whole process should not take more than one hour. This is a straightforward procedure that doesn't require special tools.

If you lose a key the process will be somewhat more complex but it is still able to be accomplished. The dealer needs to first determine the VIN of the vehicle and order an additional TWICE module and key blade that has the correct unique code. Then, they'll be required to cut the replacement key and then program it using the latest software tool known as MDI.

Key Replacement Fob

The key fob contains an internal battery that is used to lock and unlock your vehicle. The batteries have a lifespan, and they will eventually fail. It's a common issue that affects all cars. The good thing is that you can replace the battery in all key fobs, and not have to replace the entire case. You can purchase fobs replacements on Amazon that come with all the electronics already installed, which means you can simply open the case and replace the old batteries. You'll need to take out the emergency key before you replace the batteries. To do this, insert a small flathead screwsdriver into the slot in the middle. The case should split when you turn the screwdriver around it.

If you're ready to change your keys, make sure you have a spare on hand. This can save you a lot of money. If you have an additional key, ask the dealer to cut it and program it to your vehicle. This is less expensive than purchasing a new key fob.

If you don't have a spare, it is possible to add an additional key to your car, however this requires a lot of research and effort. The cost for adding a second key is about a few hundred dollars and it also requires programming of the car's computer. This can be accomplished by a professional, however it is an expensive option for [Redirect-302] most owners.

Replacement Ignition

The new SAAB 9-3 has an alarm system that is more sophisticated built around a key code. This means that in the event that you lose your only working key, replacing it with another key can be extremely expensive as the car has to have a special computer module installed, and it also needs to be specifically programmed to accept a new key. Most locksmiths cannot do this or even dealers can charge several hundred dollars just to program the new key!

If you've lost your only working key, a dealer will repair the computer in your car (known as the CIM or saab car keys TWICE) to make a replacement, and they will charge you the highest price for it. Instead, we can reprogram the EEPROM of your current car computer to make it ready to accept a second key, and save you over 50% of the amount you spend at a dealer.

If you have owned a car like the SAAB 9-3 for a long time you're aware that the ignition keys aren't very durable. If the ignition key you have isn't functioning properly, it is time to consider replacing it. They can become very sticky and the buttons can fall off. The good news is that replacing the ignition key isn't as complicated as it seems and is fairly easy to do using the proper tools.