Fiat 500 Replacement Key Fob

It might be time to replace the battery if your 500 remote key fob is not working. If you replace the battery and it's still not working the issue could be somewhere else.

At United Locksmith, we specialize in the creation of new keys for old cars. We have all the tools and parts necessary for this type of service.

Dead Coin Battery

The most common reason why your Fiat 500 key fob will not unlock or lock the doors is a dead battery. The key fob contains a coin cell battery which will quickly drain when it isn't being utilized frequently enough. If your remote started to show signs of weakness such as a loss of range or stopped working completely The battery is probably dead.

The battery in the key fob is held in place by metal retaining clips. If the clips are not tight, they can cause problems with contact that can prevent your remote from receiving power. With a small flathead screwdriver, push the clip that holds the retaining pin open to take out the battery, and replace it with a brand new one. Make sure to select a replacement with the same type of voltage, dimensions, and specification as the original battery.

The key fob could also become corroded or damaged due to exposure to water. Even a small bath in soapy water can damage the electronic chip inside. It is recommended to keep your key fob in a dry environment.

Water Damage

Water damage may be the cause of your key fob not functioning properly. The rubber seals on key fobs prevent them from being damaged by a tiny splash or drizzle of water. However, it's important to keep the keys of your car away from the washing machine, the ocean and even the pool.

The key fob contains an electronic chip that transmits a signal car's immobilizer system. The chip allows the 500 to be locked and started. If it gets wet, however it will cease to function.

If you're trying to determine whether your key fob still working it is possible to clean the internal electronics with isopropyl or electronic cleaner. However, it's recommended to purchase a replacement from a dealership rather than trying to fix an item that has been submerged by salt water.

Although a replacement fob may cost a bit of money, it's much less expensive than paying for your fiat panda key fob replacement 500 to be towed to the dealer and repaired! Additionally, you can do it yourself with the simplest of steps. Be sure to use the correct type of battery before you attempt to open your key fob. You can find step-by-step instructions for every car keyfob online.

Faulty Chip

The chip in the key fob communicates with the vehicle's immobiliser to ensure that your car is only capable of starting when the correct key is inserted. If the chip is damaged, or damaged in any way your car will not start.

Water damage or a dead phone battery are the most common causes of an unreliable chip. It is best to delegate the task to a professional locksmith, who can replace the chip in a short time and at a a reasonable price.

If your key fob ceases to function after exposure to clean water from the tap or rain, remove the battery and wipe down the electronic component with a paper towel to ensure it is fully dry before putting it back in. If the key fob doesn't work it's probably to be a damaged chip that is required to be replaced.

Some people go to their dealer when they require a new Fiat fob. However, this can be expensive. United Locksmith is the best option for you if need your fiat 500 replacement key cost key fob replaced at a reasonable cost. We have all the tools and experience needed to repair your Fiat fob in a timely and professional way.

Faulty Receiver Module

Fiat key fobs transmit a signal up 50 feet to the vehicle, which will unlock and close the doors (and start the vehicle for those with automatic transmissions). There are several reasons why the fob may not function. This could be due to a dead battery water damage, worn out buttons as well as a receiver issue. signal interference or an issue with the chip.

If the fob is placed in a pocket that suffered a severe trauma, such as being dropped on a hard floor or being washed in a wash machine the fob may not be able to communicate with the car's Body Control Module (BCM). This is because the BCM is secured and will only accept signals from a genuine original key and not another.

If this is the case, you will need to replace your fob. A professional locksmith can handle the entire process of replacing keys including programming a brand new key for your 500. They can even provide a clone fob that works just like the original (and costs only one-third of what it would cost).