Bentley Continental Key Fob Troubleshooting Tips

The Bentley Continental is an incredibly impressive vehicle to drive. The brushed metal exterior adorns the center stack. Beautiful leather and wood wrap its interior. Its powerful W12 engine produces a whopping 552 break horsepower.

The Continental key fob is sealed with rubber to stop water from damaging its electronic chip. If it gets submerged by clean water from the tap or rain it should be fine, but prolonged exposure to salty water can damage it.

Keyless entry system

The Bentley Continental comes with a keyless entry system that allows you to lock and unlock your car using remote control. This is convenient and helps you save time and effort. However, there are many reasons that your key fob could not function properly. One of them is dead batteries, water damage and receiver module issues. In some instances a malfunctioning internal chip could be the reason for the problem.

The key fob has rubber seals to prevent water from reaching the electronic chips inside. The key fob will still be wet if exposed to salty or soapy water. This could harm the chip. It is crucial to clean the key fob and allow it to dry completely before placing the battery back. If the keyfob fails to work after cleaning and drying it, then it's likely to be defective and needs to be replaced.

The metal clips on the battery of your Continental keyfob hold it in place and complete the circuit. Contact problems can occur if the clips are corroded or loose. You can fix this by looking at the battery's contacts and ensuring they're clean. Also, make sure that the battery is properly installed. Test a spare Continental Key to determine if it works. If the key has a problem it is possible to reprogram it using an OBDII scanner.

Battery

The key fob comes with a tiny coin battery within. If it's dead, the remote does not work. This is easy to diagnose and is fixable in just a few minutes. Water can also harm the battery, which will require the replacement. There are many reasons for the key fob to not be working, including worn buttons, damaged battery contacts, signal interference or an inoperative receiver module. You can reset the system if you disconnect the 12 volt batteries for a few seconds. This will allow the system to reset itself. First disconnect the negative cable, then reconnect the positive cable.

The battery in the Bentley Continental key fob can last for as long as four years, based on how frequently you use it. The battery is secured by metal clips. The clips must be secure. If they're not, then the remote will not work correctly.

If the Continental keyfob is exposed to clean water from the tap, it should be dried and cleaned using an absorbent paper towel prior to reinstalling the battery. If the chip is exposed to soapy or salty water, it could become damaged. In these instances a new keyfob may be required.

Water damage

David believes there aren't any major mechanical issues on this Continental, apart from small amounts of rust on the wheel trims and some surface corrosion that has been exposed to road grit. The boot is spacious and practical with the factory warning triangle securing to the floor, as well as an extra wheel that can be tucked away in a space-saving fashion and a the standard bentley key fob programming toolkit underneath the false floor.

The chip on the key fob is protected by rubber seals, which will allow it to function even if it gets wet. However, prolonged exposure to water could damage the chip, and it's recommended to remove your key fob of your pockets when you go swimming, kayaking or rafting, canyoning or other activities in which it could get wet.

If your key fob was submerged in water or soapy water, you may try to save it. Make use of electronic cleaners or isopropyl ethanol to clean the chip. If the key-fob fails to work after re-cleaning and drying, it might be time to replace it. If you're looking for a Bentley Continental Key Fob, ensure it's water-resistant and compatible with your vehicle from the factory.

Fault diagnosis

The Bentley Continental key fob lets you to lock and unlock your vehicle by simply pressing. This is a very convenient system and provides security and safety while driving. There are several things that could fail when it comes to your key fob. The most frequent causes are a dead battery water damage, a leak or signal interference. If the key fob you purchased isn't working, there are a few troubleshooting steps you can follow to identify the problem.

The first thing you need to look at is the battery. Be sure that it's properly inserted and the metal retaining clips are properly positioned. If the clips are not tight and the battery is not secure, it will not be able to connect properly and may not function properly. The clips for retaining should be free of corrosion and clean.

A weak car battery is another reason that causes the key fob to fail to work. The 12 volt Continental battery should be in good health to communicate with your remote keyless entry system, as well as the rest of the onboard electronics. Check your fuse box and recharge the car battery if needed.

The Bentley Continental key fob sends signals to the receiver module, which is located inside the ignition barrel. If the signal is not received, the engine will not start and the alarm will go off. If the Bentley continental key fob still not working, you should contact a professional to fix the issue.