How to Replace a Kia Sportage Replacement Key

The key of many Kia models comes with an electronic keyless entry system built in. This key typically resembles an remote control, and can be exchanged with a fresh one from a Kia dealer or a locksmith.

Key fobs may stop working due to a number of reasons, including batteries that are dead, worn-out buttons, signal interference or water damage. Here are some guidelines on how to get your kia spare key Sportage replacement key working again.

How to replace the remote key or smartkey?

The battery inside your Kia's smart key will eventually require to be replaced, whether it's a remote key as well as a push-to start key or a regular metal key that is not equipped with a transponder. This is especially relevant if your car displays a message telling that the smart key or remote has low battery power.

This is a relatively simple procedure. To replace the keyfob battery remove your mechanical key from the slot at the back of the fob. Then, pull the cover off. A small screw is in the key fob that holds the battery in the correct position. With a small screwdriver, unscrew the screw and pull out the old battery. Install the new battery and close the opening on the key fob.

When the key fob is equipped with an updated battery check it by pressing the lock and unlock buttons. If the doors unlock and lock according to your expectations, then you're set! You can now use the hands-free lock/unlock feature on your Kia whenever your fingers feel cold or you have to run some errands in Brandon.

Not all key fobs might need to be programmed (transponder chips or smart keys). This requires a programing machine, which is only available to the locksmith who works for the automotive dealer. Other keys (non transponder keys made of metal) do not require programming. If you're required to reprogramme your key, you'll have to record the key code number on the key code tag.

How do I replace the battery?

If your Kia key fob isn't responding to pressing the lock or unlock button on the fob, this is a sign that the battery needs to be replaced. A battery that is not functioning properly could cause other problems like the check engine light coming on or delayed engine cranking. Fortunately, replacing the key fob battery is a relatively easy DIY project that requires only the most basic tools.

Be sure to turn off your vehicle and close all doors before you begin. Find the small, metal or plastic piece near the bottom of the key fob. Then, jiggle it until the key is released. You can then insert this key into the handle of the door for the driver to unlock your car.

To replace the key fob battery, take off the cover at the rear and use a plastic pry bar tool to loosen the latch that holds the black negative battery cable. Remove the old battery, and then align the replacement battery so that its "+" side faces you, and the "-", negative side is facing the fob's electrical contacts. Avoid using excessive force when pushing the new CR2032 into position to avoid damage or bending the metal contacts.

After the new battery has been installed then turn the key fob off and then on in the ignition repeatedly until the door locks cycle. You can then test the Kia's Key fob again to confirm that it's working as intended.

How do I replace a smart keys

Depending on the model of your kia sportage key fob (why not find out more) Sportage, you may have an ordinary key fob or a smart key. The smart key is equipped with an embedded mechanical key blade while the standard keyfob does not. Both key fobs have an internal battery that will eventually need to be changed. Fortunately, it's quite simple and only takes about two minutes.

Before you get started before you begin, ensure that you are on a level surface with sufficient lighting and that your Kia is not on. Keep in mind that the fob has small pieces that could fall in the event of a mishap.

The first step is to locate the small release button that is located on the lower backside of the fob. It will be a circular button or rectangular slot. When you press it button, the mechanical blade will appear and you can then open the key fob.

Once the key fob is opened, take out the battery. The new battery is a the CR-2032, and it can be purchased on the internet or at your local auto parts store. When you're done, the key fob will allow you to lock the vehicle, unlock it, and then start your vehicle, even if it isn't running.

How do you replace the mechanical key

The Kia key fob is a wonderful option that lets us lock and unlock our car with the click of the button. As with all devices like a key fob, the Kia can occasionally have problems. Luckily, there are steps that can be taken to resolve these issues and ensure that our key fobs are in good working condition over the long haul.

One of the most frequent issues is a low or dead battery. This can cause the device to cease working or stop working at times. If this is the case then try replacing the battery with a fresh new one.

If this isn't enough to solve the issue, use a flathead screwdriver standard to push the plastic casing of the fob open. Be careful not to damage any internal components or scratch the plastic. When the battery is open, carefully take off the old battery and replace it with a brand new one.

Close and open the door with the mechanical key. (Every kia fob comes with a spare mechanical key which will fit into the slot). Test the fob to make sure it's functioning properly. If the device isn't working, call a locksmith or dealer to help solve the problem. To avoid locking outs in the future, make sure you get an emergency key that will work in all of the trunk and door cylinders.