How to Replace a Kia Sportage Replacement Key

The key in many Kia models comes with an electronic keyless entry system built into. This key typically resembles an electronic remote and is able to be replaced with a new one from a Kia dealer or locksmith.

Key fobs might stop working due to a variety of reasons, including batteries that are dead, worn-out buttons, signal interference or water damage. Here are some guidelines on how you can get your kia picanto car key replacement Sportage replacement key working again.

How do you replace a remote key or a smartkey?

The battery in your Kia's intelligent key will eventually have to be replaced, regardless of whether it is a remote key as well as a push-to start key or a normal metal key that is not equipped with a transponder. This is especially true if the car displays a message telling that the smart key or remote has low battery power.

It's a fairly simple procedure. To replace the battery on the key fob take out the mechanical key from the hole in the back of the key fob and break the cover. Inside the key fob will be an incredibly small screw that holds the battery in its place. By using a small screwdriver take the screw off and remove the battery that was in place. Install the new battery and close the cut on the key fob.

When the key fob is equipped with a fresh battery and you've tested it, press the locks and unlock buttons. If the doors lock and unlock as expected, then you're all set! You can now take advantage of your Kia's hands-free lock/unlock feature whenever your fingers feel cold or you have to make errands in Brandon.

Note: Certain key fobs (transponder chip or smart keys) may require their programming completed. This requires a specific programming machine that only the dealer or automotive locksmith has access to. Other keys (non-transponder metal keys) do not require programming. If you want to change the programming of your key, you'll have to note the key code's number on the key code tag.

How do I replace the battery?

If the Kia key fob does not respond to pressing the lock/unlock button, it is most likely that the battery is low. A low battery may cause other issues, such as the check engine light flashing or the engine not working properly. It is easy to replace the key fob batteries with only two tools.

Make sure you turn off your vehicle and shut all doors prior to beginning. Locate the small metal or plastic piece at the bottom of your key fob, and play with it until a metallic key pops out. Then, you can put the key into the handle on the door of your driver to unlock your car.

To replace the key fob's battery, remove the rear cover and use a pry bar tool to loosen the latch holding the black negative battery cable. Take the old battery out, and then align the replacement battery to ensure its "+" side is facing you, and the "-" negative side is facing the fob's electrical contacts. Avoid using excessive force when pushing the new CR2032 into place to avoid damaging or bending the metal contacts.

Once the new battery is installed after which you turn the key fob off and then on in the ignition for a few times until the door locks. You can then test your Kia's keys fob once more to ensure it's working as intended.

How can you replace the smart key?

You may have either a standard keyfob, or a Smart Key, based on the model of Kia Sportage. The difference between the two is that the smart key has a small mechanical key blade tucked inside it, while the standard key fob does not. Both types of key fobs have an internal battery which eventually needs to be replaced. Fortunately, this is quite simple and takes only two minutes.

Make sure you turn off your Kia and be on a level and well-lit surface prior to you begin. Be aware that the fob has small pieces that could fall in the event of a mishap.

The release button for the small size is located on the lower backside. It could be an oval silver button or a rectangular slot. After pressing this button button, the mechanical blade will be released and you will be able to open the key fob.

Once you have the key fob open then you can remove the old battery, and replace it. The new battery is a C2032, and can be bought online or in your local auto parts shop. Once you're done, you should be able to lock or unlock your car using your key fob even if your engine isn't running!

How do you replace the mechanical key

The Kia key fob is a great feature that lets us lock and unlock our car at the touch of an button. Like any other device there are issues with it at times. Luckily, there are steps to take to solve these issues and ensure that our key fobs are in good working order for the long term.

One of the most frequent problems is a low or dead battery. This can cause your fob to stop working or operate intermittently. If this is the case try replacing the battery with a fresh new one.

If this doesn't resolve the problem, try using a standard flathead screwdriver to open the fob's plastic casing. Be careful not to harm any internal components or scratch the plastic. After the battery has been removed then replace it with a brand new one.

When the new battery is in, close and then open the doors using the mechanical key (every Kia Ceed Key Fob Replacement fob comes with an emergency mechanical key that will fit in the slot). Test the key fob to ensure it's working as intended. If the key fob isn't functioning, contact an expert locksmith or dealer to help resolve the issue. To avoid lockouts in the future, make sure you get an emergency key that will work on all door and trunk cylinders.