Peugeot 208 Key Replacement

It is best to delegate the replacement of Peugeot keys for 208 to auto locksmiths equipped with the necessary equipment and technical knowledge. They will be able to make and program new keys faster than a dealership would and at a lower price.

If your key fob stopped locking or unlocking your doors it is likely due to a dead coin battery. There are other reasons why the key may be malfunctioning.

Dead Coin Battery

A dead coin battery will stop your Peugeot 208 from locking or unlocking and will not allow you to start the engine. If this is the situation, you'll need apply the backup starting technique that's described in your vehicle's owner manual.

The spark plugs might also be worn out. The spark plugs ignite fuel to start the engine. They have a limited life span. If they are not used enough, they will eventually fail.

There is a straightforward solution to this issue. Verify the voltage of your battery with a multimeter. If it is below 11.5 Volts and you are not satisfied, then it is time to replace it. If the battery has corrosion it is crucial to clean its contacts. This can be done by removing the rubber cover from the two battery terminals and then using a wirebrush to remove any parts of the battery that are corroded. After that, you need to connect the positive and negative pole cables.

Water Damage

If your 208 does not start and the battery has not gone flat, you should inspect the spark plugs. It could be that they are simply too filthy and don't spark. This can be fixed by cleaning the spark plugs in a workshop.

peugeot 207 key cars use a key with a transponder that is compatible with the immobiliser. This ensures that only a valid key is able to turn the engine. If the chip inside the Peugeot key is damaged, then it will not send the correct signal to the vehicle.

This is a common problem that can occur due to water damage. This is a common issue in warmer climates where the vehicle has been exposed to rain or snow. If this is the case, contact a reputable auto locksmith who will have all the tools and equipment needed to modify the new key. They'll also have the latest technology and equipment needed to make a Peugeot smart key. The process should take no more than 15 minutes.

Contacts to the battery are not working properly.

Peugeot replaced the old transponder chips using a new type that uses electronic components mounted on a circuit board. This new technology works great when it's brand new but as time passes, the circuit boards begin to wear out and stop functioning properly.

This could stop the immobiliser chip activating which means that your car won't start. If this is the case, it's recommended to seek out a Peugeot specialist or locksmith.

The most frequent issue is when the battery inside the key fob starts to die. This causes the blade of the key to stop feeding into your lock. A car locksmith will replace the battery, and then cut a new key blade for you. This is a simple fix.

Faulty Receiver Module

It could be that the receiver module is malfunctioning when your Peugeot key fob fails to function after being dropped on the floor, or exposed to a stormy rainstorm, or accidentally washed. The receiver module is responsible for transmitting radio signals to the onboard computer which manages the central locking system of your peugeot key replacement vehicle.

The key fob itself is fitted with rubber seals that block water from reaching the electronic chip inside. The chip can be damaged by water when it is exposed to water for long periods of period of. Submerging the key fob in the ocean at the beach or throwing it into the pool can be particularly damaging due to the high salt content.

If your Peugeot spare key fob isn't working You'll need the module replaced. This is only done by an Peugeot specialist or an expert auto locksmith. Unlike other cars, Peugeot keys are protected by an unique immobilizer system that requires the right coding in order to start the engine. It is for this reason that you should only rely on the Peugeot locksmith to design and program a replacement.

Computer on-board is not working properly

The on-board computer in your Peugeot is responsible many functions in your car including airbags and power windows. If something goes wrong with these systems, it will typically show a code that identifies the problem. This code will be stored in the system until the issue is resolved. This can often mean that the on-board computers to be replaced.

One of the main reasons for the airbag light flashing is loose or corroded connections within the airbag sensor. This could be due to wear and tear, ageing, or exposure to salt and moisture. This issue must be addressed as soon as you can, because an airbag that's malfunctioning could be dangerous in the event of an accident.

If you encounter the error "card not found" on your Peugeot key fob, the battery in the key fob could be dead or weak. This prevents the key fob from transmitting a signal that will disable your vehicle's immobilizer. You can test this by pressing the unlock button on the key fob and then trying to start your car. If this doesn't work, then the key battery will need replacing.