How to Replace a Kia Sportage Replacement Key

The key in many Kia models has an entry system that is keyless into. This key is similar to a remote control and can be exchanged with a Kia dealer.

Key fobs may stop working due to a variety of reasons, such as an inactive battery, worn out buttons signal interference, or water damage. Here are some helpful tips on how to get your Kia Sportage replacement key working again.

How to replace a smartkey or remote key?

The battery inside your Kia's smart key will eventually need to be replaced, whether it is a remote key as well as a push-to start key or a normal metal key that is not equipped with an electronic transponder. This is especially relevant if your vehicle shows a message that states the remote or smart keys aren't powered.

It's a relatively simple process. In order to replace the key fob battery take out the mechanical key from the hole in the back of the key fob and pry open the cover. A small screw is found inside the key fob, which holds the battery in place. Utilizing a small screwdriver take the screw off and pull out the battery that was in place. Install the new battery and then close the opening on the key fob.

Once the key fob has an updated battery check it by pressing the lock and unlock buttons. If the doors unlock and lock in the same way, you're all set! You can now utilize the hands-free feature to lock and unlock your Kia whenever your fingers start to get cold or you have to run errands around Brandon.

Not all key fobs may need to be programmed (transponder chips or smart keys). This requires a particular programming machine that only the dealer or locksmith has access to. Other keys (non-transponder metal keys) don't require programming. If you need to reprogramme your key, it is necessary to record the key code number on the key code tag.

How do you replace a battery?

If your Kia key fob isn't responding to pressing the lock or unlock button on the fob, it is a good indicator that the battery needs to be replaced. A low battery may also cause other issues like the check engine light flashing on or delayed cranking of the engine. It is easy to replace the key fob batteries with only some tools.

Before you begin be sure that your vehicle is turned off and that all doors are closed. Find the small metal or plastic piece near the bottom of the key fob. Then, jiggle it until the metal key comes out. The key can be inserted into the driver door handle to unlock your car.

To replace the key fob battery, take off the cover from the back and use a plier bar tool to release the latch that holds the black negative battery cable. Remove the old battery and orient the new one to ensure that the "+" positive side is facing you, and the "-" negative side is facing towards the fob's electrical contacts made of metal. Avoid using excessive force when pushing the new CR2032 into place to avoid breaking or bending the steel contacts.

After installing the new battery, turn the key fob on and off in the ignition until the door locks up. Then, you can test your Kia key fob to check whether it's working again.

How do you replace a smart keys

Depending on the model of your Kia Sportage, you may have a standard key fob or a smart key. The difference between them is that the smart key comes with the small blade of a key tucked inside it, while the standard fob does not. Both key fobs have batteries that eventually require replacing. It's an easy process that takes just two minutes.

Before you get started before you begin, make sure that you are on a level surface with sufficient lighting and that your kia picanto key fob replacement is turned off. Also, remember that there are small parts inside the fob which could be snagged if not cautious.

The release button for the small size is located on the lower backside. It's either an oval or circular slot. You can open the key fob by pressing the button.

Once you have the key fob opened then you can remove the old battery, and replace it. The new battery should be a CR-2032, and can be purchased online or at your local auto parts store. When you are done it should be possible to lock or unlock your car with your key fob even if your engine isn't running!

How to replace a mechanical key

The Kia keyfob is a great convenience that lets us lock or unlock our car simply by pressing one button. Like any other device it may have issues at times. Luckily, there are steps to take to troubleshoot these issues and ensure that our key fobs are in good working order in the long run.

One of the most common problems is a weak or dead battery. The fob could be able to stop working altogether or even to stop working intermittently. If this is the case then try replacing the battery with a new one.

If this doesn't fix the issue, try using a standard flathead screwdriver to wedge open the fob's plastic casing. Be careful not to damage any internal components or scratch the plastic. When the battery is open, carefully take off the battery that was removed and replace it with a brand new one.

After the new battery has been put in, close and open the doors using the mechanical key (every Kia fob comes with an emergency mechanical key that will fit in the slot). Test the key fob to confirm it's working properly. If the key fob isn't functioning, contact an expert locksmith or dealer to help solve the problem. Make sure they cut you an emergency key that functions for all trunk and door cylinders to avoid lockouts in the future.