How to Replace a Kia Sportage Replacement Key

The key on many Kia models comes with an entry system that is keyless into. The key functions like a remote control, and is exchangeable by an Kia dealer.

Key fobs might stop working for a variety of reasons, such as the battery of the coin is dead worn buttons water damage, signal interference and a malfunctioning receiver module. Here are some suggestions on how to get your Kia Sportage replacement key working again.

How do you replace the remote key or smart key

No matter if your Kia comes with an intelligent key, remote key, push-to-start keys, or a regular non-transponder steel key The battery inside these keys will eventually need replacement. This is particularly the case if your car displays a message indicating that the remote or smart keys are in poor condition.

Luckily, it's a relatively simple process. To replace the battery on the keyfob, remove your mechanical key from the slit at the back of the fob. Then, you need to pry the cover off. Inside the key fob there will be an incredibly small screw that holds the battery in place. With a small screwdriver, take the screw off and pull out the battery that was in place. Then, insert the new one and close the slit inside the key fob.

When the key fob is equipped with a fresh battery and you've tested it, press the lock and unlock buttons. You're good to go if the doors lock and unlock as expected. You can now use the hands-free feature to lock and unlock your Kia whenever your fingers start to get cold or you need to do some errands in Brandon.

Not all key fobs may need to be programmed (transponder chips or smart keys). This requires a specific programming machine that only the dealer or locksmith has access to. Other keys (non transponder metal keys) do not require programming. If you want to change the programming of your key, you'll have to write down the key code's number on the key code tag.

How do I replace a battery

If your Kia key fob is not responding to pressing the lock or unlock button on the fob, it is a clear indication that the battery should be replaced. A low battery can also cause other issues, such as the check engine light flashing or the engine not working properly. Fortunately, replacing the key fob battery is a fairly simple DIY task that requires only the most basic tools.

Before beginning the process be sure that your vehicle is off and that all doors are shut. Find the small, metal or plastic piece on the bottom of your key fob, and move it until a metal key pops out. You can then put the key into the handle of the door for the driver to open your car.

To replace the battery in the key fob remove the cover on the rear. Make use of a plastic pry tool to loosen up the latch that holds the black negative cable. Remove the old battery, and then align the replacement kia key battery to ensure its "+" side faces you, and the "-", negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into position without putting too much force on it to avoid damaging or breaking the contacts of the metal.

Once the new battery has been installed and the key fob is turned on, turn it off and on in the ignition until the door locks cycle. You can then test your Kia's key fob again to confirm that it's working as intended.

How do you replace the smart key?

Depending on the model of the Kia Sportage, you may have an ordinary key fob or a smart key. The smart key features an embedded mechanical key blade while the standard keyfob does not. Both kinds of key fobs come with batteries inside that will eventually need to be replaced. It is a simple process which takes just two minutes.

Before you begin it is essential to make sure that you are on a level surface with good lighting and that your Kia is turned off. Be aware that there are tiny pieces inside the fob which could fall out if not cautious.

The small release button is located on the lower backside. It could be an oval silver button or a rectangular slot. You can open the key fob by pressing the button.

After the key fob has been removed, you can remove the battery. The new battery is a CR-2032 that can be purchased online or at your local auto parts store. After you've finished, your key fob should allow you to lock the vehicle, unlock it, and then start your vehicle, even if it isn't running.

How to replace a mechanical key

The Kia keyfob is an excellent convenience that allows us to lock or unlock our car by simply pressing the button. Like any device it is possible that the Kia key fob may have issues. Luckily, there are ways to fix these issues and keep our key fobs in good working condition in the long run.

One of the most frequent issues is a low or dead battery. This could cause your device to stop working or work intermittently. If this is the case try replacing the battery with a new one.

If this isn't enough to solve the issue, you can use a flathead screwdriver standard to wedge the fob's casing made of plastic open. Be careful not damage any internal components or scratch the plastic. Once the battery is removed and replaced, you can replace it with a brand new one.

Once the new battery is in, close and open the doors with the mechanical key (every Kia fob comes with an emergency mechanical key that can fit in the slot). Test the key fob to verify that it's functioning properly. Contact a dealer locksmith to resolve the problem if the fob is still not working. Make sure they make you an emergency key that can work for all door and trunk cylinders to avoid lockouts again.