Bentley Continental Key Fob Troubleshooting Tips

The Bentley Continental is an incredibly impressive car to drive. The center stack is embellished with brushed metal, and the interior is covered in beautiful wood and leather. Its powerful W12 engine generates 552 break horses of power.

The Continental key fob is encased with rubber to prevent water from damaging the electronic chip. If it is submerged in clean tap water or rain it is fine, but prolonged exposure to salty water could damage it.

Keyless entry system

The Bentley Continental comes with a keyless entry system, which allows you to lock and unlock your vehicle using remote controls. This is convenient, and you will save time. However, there are several reasons that your key fob could stop working. One of them is dead batteries, water damage and receiver module issues. In some cases the issue could be caused by a malfunction of the internal chip.

The key fob comes with rubber seals to prevent water from getting to the electronic chips inside. However the key fob might still be soaked if exposed to salt water or soapy water. This could damage the chip. It is important to clean the key fob thoroughly and let it dry completely prior to placing the battery back. If the keyfob does not work after cleaning it and drying it, then it's likely to be defective and needs to be replaced.

The metal clips on the battery of your Continental keyfob are what hold it in place, and complete the circuit. If the clips are loose or corroded, it can cause contact issues. Make sure to check the battery's contacts to ensure they are clean. Also, make sure the battery is properly inserted. If you have a spare Continental key, try it to see whether it is working. If the key is damaged it is possible to reprogram it using an OBDII scanner.

Battery

The key fob contains tiny batteries that are the size of coins. When it is dead, the remote won't work. It is easy to determine the cause and replace in only a few minutes. Water can also damage the battery, which will require a replacement. The key fob may not work for a number of reasons, including worn-out buttons, damaged contacts in the battery, signal interference or a dead module. You can reset the system by disconnection of the 12 volt battery for a short period of time. This will allow the system itself to reset itself. Connect the positive cable first, then disconnect the negative.

The battery in the Bentley Continental key fob can last up to four years, depending on how often you use it. The battery is restraining with metal clips that secure it in place and complete the circuit. The clips should be secure but if not, the remote will not work properly.

If the Continental keyfob is exposed clean water from the tap, it should be dried and cleaned using a paper towel before reinstalling the battery. If the chip is exposed to salty or soapy water, it could be damaged. In this case you'll have to purchase a new key fob.

Water damage

David does not believe there are any major mechanical issues with this Continental car, besides minor rust damage to the wheel trims, and a bit of surface corrosion in places exposed to road grit. The boot is roomy and practical with the factory warning triangle securing to the floor, plus the space-saver spare wheel as well as a the standard Bentley toolkit beneath the false floor.

The chip on the key fob is protected by rubber seals, which should keep it functioning even if it gets wet. However prolonged exposure to water could damage the chip, which is why it's best to take your key fob out of your pocket whenever you go on kayaking, swimming, rafting, canyoning, or any other activity where it may get wet.

If your key fob was submerged in soapy water from the washing machine or submerged in ocean water at the beach, it may still be worth trying to save it by cleaning the chip with isopropyl alcohol, or an electronic cleaner. If the key fob doesn't seem to function after re-cleaning it and drying, it might be time to replace it. If you're in the market for a Bentley Continental key fob, make sure to select one that is waterproof and specifically designed to work with your vehicle.

Fault diagnosis

The bentley key programming [Read the Full Document] Continental keyfob enables you to lock or unlock your vehicle with one click. This is a convenient system that ensures security and safety while driving. However, there are several things that can happen to your key fob. The most frequent causes are a dead coin battery signal interference, water damage or a damaged internal chip. If the key fob you purchased isn't working there are a few troubleshooting actions you can take to diagnose the problem.

The first thing to inspect is the battery. Check that it is properly inserted and the metal retaining clips are in the correct position. If the clips are not tight the battery won't have a secure connection and may not work properly. Furthermore, the retaining clips must be clean and free of corrosion.

Another reason that is commonly cited for the key fob not working is the weak battery in your bently car key. The 12 volt Continental battery should be in good condition to communicate with your remote keyless entry system as well as the rest of the onboard electronics. It is recommended to check the fuses and recharge the car battery when needed.

The Bentley Continental keyfob sends a message to the receiver module which is located in the ignition barrel. If the signal isn't received, the engine will not start and an alarm will sound. If the Bentley continental key fob still not working, seek out a professional to fix the issue.