How to Replace a Hyundai I10 Key Fob Battery

The Hyundai i10 has a stylish interior that competes with the Volkswagen UP and Citroen C1, as well as SEAT Ibiza. Its interior is higher-end than its rivals such as the Citroen C1, Volkswagen UP and SEAT Ibiza.

Hyundai's keyfob can accomplish a lot for you. It can lock and unlock your vehicle remotely. It also comes with a mechanical key, which can be used in the event that the battery of the fob fails.

Dead Coin Battery

Key fobs allow motorists to lock their vehicles and then start them, without having to insert a physical key into the ignition. It does this through radio frequency signals that connect to the car's onboard computer.

The battery inside the key fob is responsible for this communication and will eventually wear out and require replacement. Depending on the model of your Hyundai key fob, it could or may not show a warning before the battery is dead. It is best to have a spare key fob with you so that you can quickly replace the battery when it starts to wear out.

After the new battery is installed, the key fob has to be reprogrammed with the car. It is possible to do this using an OBDII or Hyundai Digital Key scanner, but it is usually easier to do at your Reno home. To accomplish this, follow the instructions in the owner's manual or look on YouTube for "how to open and replace the Hyundai key fob battery." Be sure you record the old battery's code or take a picture of it prior to taking it off. it.

Once the key fob has been reprogrammed, it should work again. If it does not work you'll have to go to an authorized dealer for a replacement or call locksmith. They'll have the equipment and know-how to fix the issue.

Water Damage

A key fob is an extremely useful piece of technology. It allows you to lock your vehicle from your home, to roll down your windows from outside and even start your vehicle. But, it's not impervious to damage and will eventually wear out due to regular use. Fortunately, the process of replacing a Hyundai I10 key fob battery is relatively straightforward and cost-effective.

It's not uncommon to drop your key fob into the water, a puddle or even a washing machine. It is possible to save it by taking action quickly. Water isn't a good mix when it comes to electronics and a wet key fob could cause a variety of issues, such as corrosion, short circuits, and even complete failure.

The first thing you need to do is try to get as many gallons of water out as you can. Shake out any visible moisture by flipping the fob. You might also be able to put it on top of a radiator or use a hairdryer to speed up the process. After you've removed all the moisture you can put the fob somewhere warm where it will dry out for a few days.

Then, you can open the fob in order to remove the battery that was in it. Most Hyundai key fobs with the i10 model use the same type of battery that's found in a lot of quartz watches. They're very easy to replace. Once you've replaced your battery, be sure to take a picture or make an outline of how it's placed prior to closing the fob.

Poor Battery Contact

It's possible your key fob's battery is getting worn out. This is a common problem and the remote usually starts showing signs of trouble well before it goes out completely. Check that the metal clips aren't corroded, and they're tight. If they are, you can use a wirebrush and the cleaning solution for batteries to clean them. Then, ensure that you are using a button-cell battery that is identical in size, voltage and specification of the original.

It may be an indication that your alternator, the part that charges the battery while the engine is running, is not working as it should. A malfunctioning alternator could drain the battery quickly and cause the warning light to come on.

A quick check of the voltage can aid in determining if this is the case for your Hyundai. If the battery is good there's a chance that there is a problem with the circuit board or some other part of the key fob. You can open the key fob by pressing the small metal tab or button on either the back or front of the device. After removing the cover, put in the new CR2032 battery, and ensure that all connections are made.

Reprogramming

Hyundai offers keyless entry in the majority of its models. This makes traveling around Littleton and Parker, CO, easier than ever. You can use the remote to start your car, open the doors, and lock them. But, it's not completely safe, and a broken key fob can cause problems. If your Hyundai key fob doesn't work it could need to be reprogrammed to work with your vehicle.

The first thing to do is to remove the battery. Typically the button cell battery is contained within a plastic tab. If you remove the tab and replace the battery, be sure to use the same size and voltage as your old battery.

After the battery is replaced, close the tab and replace retaining clips. Check the key fob once more to ensure it functions.

If the key fob still does not work, it may be time to contact an authorized locksmith or dealer. A dealer or locksmith will be able to cut you a new remote and key, and program it to ensure it is compatible with your vehicle. The cost for this service is typically charged, but it is worth it if your goal is to keep your Hyundai key fob running. They can also help you find the best hyundai i30 replacement key key fob to meet your requirements.