How to Replace a Kia Sportage replacement kia key Key

For a number of kia spare key; content, models keys, the key has an integrated keyless entry system. This key typically resembles the remote control and is able to be replaced by a new one purchased from an Kia dealer or a locksmith.

Key fobs might stop working due to various reasons, such as the battery of the coin is dead worn buttons, signal interference, water damage and a faulty receiver module. Here are some suggestions on how you can get your Kia Sportage replacement key back to working.

How to replace a remote key or smartkey

Whether your Kia is equipped with an intelligent key, remote key, push-to-start keys, or a regular non-transponder steel key, the battery in these keys will eventually need replacing. This is particularly true if the car displays a message telling that the smart key or remote has a low battery.

Luckily, this is quite simple to do. To replace the battery of the key fob, remove the mechanical key from the slit on the back of the key fob. You then need to break the cover. Inside the key fob, there will be tiny screws that hold the battery in place. Using a small screwdriver, remove the screw and remove the old battery. Insert the new battery and close the opening on the key fob.

Test the key fob by pressing the lock and unlock buttons. If the doors lock and unlock in the same way, you're all set! You can now utilize Kia's hands-free lock/unlock function when your fingers start to get cold or you have to go on errands around Brandon.

Note: Certain key fobs (transponder chip or smart keys) may require their programming completed. This requires a special programming machine that only the dealer or automotive locksmith has access to. Other keys (non-transponder metal keys) do not require programming. If your key needs to be reprogrammed, then you must be aware of the key code written on the tag that identifies the key and save the number in a secure place.

How do you replace a dead battery?

If the Kia key fob doesn't respond when you press the lock/unlock button, it is likely that the battery is depleted. A weak battery could cause other issues, like the check engine light appearing or the engine not working correctly. Fortunately, replacing the battery on the key fob is a relatively simple DIY project that requires only the most basic tools.

Before you begin ensure that your vehicle is turned off and that all doors are closed. Find the small, metal or plastic piece that is on the bottom of your key fob and jiggle it until a metal key slips out. This key can be placed inside the driver door handle to unlock your car.

To replace the battery in the key fob remove the cover that covers the rear. Use a plastic pry tool to loosen the latch that holds the black negative cable. Remove the old battery and align the new battery to ensure that the "+" positive side faces you and the "-" negative side is facing towards the fob's metallic electrical contacts. Push the new CR2032 battery straight into position with care to avoid using too much force to avoid damaging or breaking the contacts of the metal.

Once the new battery has been installed, turn the key fob off and then turn it on in the ignition several times until the door locks. You can then test your Kia's keys fob once more to ensure it's working properly.

How can you replace the smart key?

Depending on the model of the Kia Sportage, you may have an ordinary key fob or a smart key. The smart key has an embedded mechanical key blade while the standard key fob does not. Both types of key fobs are equipped with batteries inside which eventually needs to be replaced. This is a simple procedure which takes just two minutes.

Before you get started it is essential to make sure that you are on a level surface with sufficient lighting and that the Kia is off. Be aware that the fob can contain tiny parts that could fall when you're not careful.

The release button for the small size is located on the lower backside. It's either an oval or circular slot. Once you press this mechanical key blade, it will appear and you can then open the key fob.

Once the key fob is opened, remove the battery. The new battery is the CR-2032, and it can be purchased on the internet or at your local auto parts store. Once you're done, your key fob will allow you to lock and unlock your vehicle, even if it isn't running.

How do you replace the mechanical key

The Kia key fob is a fantastic convenience that allows us to lock and unlock our car with the press of one button. But like any device it will encounter issues at times. Luckily, there are methods to fix these issues and keep our key fobs in good working condition for the long term.

A dead or drained battery is one of the most frequent problems. The battery could cause the device to stop working or work intermittently. If this is the problem then replace the battery with an entirely new battery.

If this isn't enough to solve the issue, you can use the flathead screwdriver that is standard to push the fob's plastic casing open. Be careful not to damage any internal components, or scratch the plastic. When the battery is open, carefully take off the old battery and replace it with a brand new one.

Once the new battery is in, close and open the doors using the mechanical key (every key fob in the kia has an emergency mechanical key that can fit in the slot). Test the key fob to verify that it's working as intended. If the key fob isn't functioning, contact a locksmith or dealer to resolve the issue. Make sure they cut you an emergency key that functions for all trunk and door cylinders, to avoid lockouts in the future.