How to Replace a Kia Sportage Replacement Key

For a variety of Kia models, the key contains a built-in keyless entry system. This key is similar to the remote control, and can be exchanged by an Kia dealer.

Key fobs can stop working due to a variety of reasons, including batteries that are dead, worn buttons, water damage, signal interference, and a defective receiver module. Here are some suggestions to help you get your Kia key fob that is a replacement for the sportage again.

How to replace the remote key or the smart key?

Whether your kia sportage key fob comes with an intelligent key, remote key, push-to-start key, or a regular non-transponder steel key the battery in these keys will eventually require replacement. This is particularly relevant if your car displays a message telling that the smart or remote key is not powered by the battery.

It's a fairly simple procedure. In order to replace the key fob battery take the mechanical key from the slit on the back of the key fob. Then break the cover. Inside the key fob, there will be the small screw that holds the battery in its place. With a small screwdriver, take the screw off and pull out the old battery. Then, insert the new one and close the slit in the key fob.

Once the key fob has an updated battery and you've tested it, press the locks and unlock buttons. If the doors lock and unlock as expected, then you're set! You can now take advantage of Kia's hands-free lock/unlock function whenever your fingers feel cold or you need to go on errands around Brandon.

Note: Certain key fobs (transponder chip or smart keys) might require their programming done. This requires a particular programming machine that only the dealer or locksmith has access to. Other keys (non-transponder metal keys) do not require programming. If your key needs to be programmed again, you must be aware of the key code stamped on the tag that identifies the key and record it in a safe location.

How do you replace a battery?

If the Kia key fob doesn't respond to pressing the lock or unlock button, it is most likely that the battery is insufficient. A low battery may cause other issues, like the check engine light turning on or the engine not running correctly. Fortunately replacing the key fob battery is a simple DIY project that requires only some basic tools.

Be sure to turn off your vehicle and shut all doors prior to beginning. Find the small metal or plastic piece that is located at the bottom of the key fob. Jiggle it until the metal key comes out. The key can be placed inside the driver door handle to unlock your car.

To replace the key fob's battery, take off the cover from the back and use a plastic bar tool to release the latch holding the black negative battery cable. Remove the old battery, and then place the new battery in a way that its "+" side is facing you and the "-", negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into position and avoid excessive force to avoid damaging or breaking the contacts made of metal.

After you have installed the new battery and turning the key fob off and on in the ignition until the door locks up. Then you can test your Kia key fob and see whether it's functioning properly again.

How can you replace the smart key

There is a possibility of having a standard keyfob, or a Smart Key depending on the model of kia picanto key fob (visit web site) Sportage. The smart key has an embedded mechanical key blade, unlike the standard key fob, which does not. Both types of key fobs have an internal battery which eventually needs to be replaced. Fortunately, this is an easy task that will take about two minutes.

Make sure to shut off your Kia and sit on a flat, well-lit surface before you begin. Keep in mind that the fob has tiny parts that could be thrown off if you're not careful.

The first step is to locate the small release button on the lower backside of the fob. It can be an oval silver button or a rectangular slot. After pressing this button the mechanical key blade will pop out and you can then open the key fob.

Once you have the key fob opened it is easy to take off the old battery and replace it. The new battery should be a CR-2032, and can be bought online or from your local auto parts store. After you're done, your key fob should permit you to lock the vehicle, unlock it, and then start your vehicle even if it's not running.

How to replace a mechanical key

The Kia keyfob is a great convenience which allows us to lock or unlock our car simply by pressing a button. Like any other device it will encounter issues from time to time. Luckily, there are methods to troubleshoot these issues and keep our key fobs in good working order in the long run.

One of the most common issues is a low or dead battery. The battery could cause the device to stop working or work intermittently. If this is the case then try replacing the battery with a fresh new one.

If this isn't enough to resolve the problem Try using a standard flat-head screwdriver to break open the fob's plastic casing. Be careful not damage any internal components or scratch the plastic. Once open, carefully remove the battery you have been using and replace it with a brand new one.

When the new battery is in, close and open the doors using the mechanical key (every Kia fob has an emergency mechanical key that can fit into the slot). Test the key fob to make sure it is working correctly. If the device not working, contact an expert locksmith or dealer to help solve the issue. To avoid future lockouts, ensure you purchase an emergency key that can work on all trunk and door cylinders.