Bentley Continental Key Fob Troubleshooting Tips

The Bentley Continental is an incredibly impressive vehicle to drive. The center stack is embellished with polished metal, while the interior is adorned with exquisite leather and wood. Its powerful W12 engine generates 552 break horses of power.

The Continental key fob comes with rubber seals that stop water from destroying the chip's electronic components. If it gets submerged by clean water from the tap or rain it should be fine, however, prolonged exposure to salty water could harm it.

Keyless entry system

The Bentley Continental comes with a keyless entry system that allows you to lock and unlock your car with remote control. This is convenient and can help you save time and effort. There are a myriad of reasons your key fob's device may stop working. A few of them are dead batteries, water damage or receiver module issues. In certain cases the issue could be caused by a malfunction in the internal chip.

The key fob is encased with rubber to prevent water from entering the electronic chips. However the key fob could be wet even if exposed to soapy or salty water. This could damage your chip. It is crucial to clean the key fob and allow it to dry completely before putting back the battery. If the keyfob fails to work after cleaning and drying it, then it is likely faulty and needs to be replaced.

The battery in your Continental key fob has clips of steel that keep it in place and complete the circuit. Problems with contact can occur if the clips are corroded or loose. Check the battery's contacts to ensure they are clean. Also, ensure that the battery is firmly installed. Test with a spare Continental Key to determine if it works. If the key is not working, you can reprogram it with an OBDII scan.

Battery

The key fob contains tiny batteries that are the size of coins. The remote will not function when the battery for the coin is dead. It is easy to determine the cause and can be fixed in a few minutes. Water can also damage the battery, which will require replacing it. The key fob might not work for a number of reasons. These include worn-out buttons, faulty contacts in the battery, signal interference, or a dead module. It is possible to reset the system by disconnecting the 12 volt battery for a short period of time. This will allow the system itself to reset. Disconnect the negative cable first and then reconnect the positive cable.

The battery in the Bentley Continental key fob can last up to four years, depending on how frequently you use it. The battery is secured by metal clips. The clips must be secure. If they are not tight, the remote won't function properly.

If the Continental key fob is exposed to clean tap water, it should be cleaned with a paper towel and allowed to dry before putting it back in the battery. If it is exposed to salt or soapy water, the chip may be fried. In these instances it is likely that a new keyfob would be needed.

Water damage

David believes that there are any major mechanical problems on this Continental. There is a little surface corrosion where the wheels have been exposed to road grit. The boot is roomy and practical with the factory warning triangle securing to the floor. There's also an extra spare wheel that is space-saving and the standard bentley arnage key fob toolkit under the false floor.

The chip inside the key fob is protected by rubber seals, which will allow it to function even when it's wet. However long-term exposure to water may damage the chip, so it's advisable to take your key fob out of your pockets when you go swimming, kayaking and rafting, canyoning or other activities where it might get wet.

If your key fob has been soaked in soapy water from the washing machine or submerged in ocean water at the beach, it might be worthwhile to keep it from being damaged by cleaning the chip using isopropyl alcohol or an electronic cleaner. If your key fob still does not work after cleaning and drying it then you may have to replace it. If you are looking for a Bentley Continental Key Fob, be sure that it's water-resistant and factory-paired to your car.

Fault diagnosis

The Bentley Continental key fob allows you to lock and unlock your vehicle by simply pressing. It is easy to use and ensures security and safety while driving. There are a few things which could fail with your key fob. The most common reasons are a dead battery water damage, or signal interference. There are some troubleshooting methods you can use to diagnose an electronic key fob not functioning.

The first thing you need to look at is the battery. Make sure that it is properly inserted and the retaining clips made of metal are in the correct position. If the clips are loos they could cause the battery to not be getting a good contact and won't work effectively. The clips used to hold them must be free of corrosion and clean.

A car battery that is weak is a common reason for the key fob not to function. The 12 volt battery inside your Continental must be in good health to communicate with the remote keyless entry system as well as the rest of the electronics onboard. You should check your fuses and recharge the car battery if needed.

The Bentley Continental key fob sends a signal to the receiver module which is located within the ignition barrel. If the signal is lost, the engine will not start and the alarm will go off. If the Bentley Continental key fob does not work, you should speak with a professional.