Peugeot 208 Key Replacement

Peugeot 208 key replacement car keys peugeot is best left to professional auto locksmiths who have the appropriate equipment and technical know-how. They can make and program new keys faster than a dealership would and at a cheaper cost.

If your key fob has stopped locking or unlocking your doors it is likely due to a dead coin battery. There are other reasons that the key may be malfunctioning.

Dead Coin Battery

A dead battery in the coin compartment will hinder your Peugeot 208 from locking or unlocking and won't start the engine. In this instance you'll need to use the alternative starting method described in your vehicle owner's manual.

Another reason why your 208 might not be starting is that the spark plugs have worn down. Spark plugs are what ignite the fuel to start the engine. They only last for a certain amount of time. If they aren't utilized enough to last, they'll eventually fail.

There is a simple solution for this issue. Verify the voltage of your battery with a multimeter. If it's below 11.5 volts and you are not satisfied, then it is time to replace it. If the battery has corrosion it is crucial to clean its contacts. This can be done by lifting the rubber covers that protect the two terminals of the battery and using wire brushes to clean any parts that are corroded from the battery. Then, you should reconnect the positive and negative pole cables.

Water Damage

If your 208 will not start and the battery hasn't gone flat, you should inspect the spark plugs. It could be that they're dirty and don't spark. The spark plugs can be cleaned in an workshop.

Peugeot automobiles use a transponder style key that works with the car's immobiliser system. This ensures that only the right key is able to turn the engine. If the chip inside the Peugeot key is damaged, then it won't send the proper signal to the vehicle.

This is a typical issue that can occur due to water damage. This is a frequent issue in colder climates where the vehicle is exposed to rain or snow. In this case, contact a reputable locksmith who has the tools and equipment required to change the key's programming. They also have the most up-to-date technology and equipment needed to make a Peugeot 208 smart key. The process should take no more than 15 minutes.

Contacts to the battery are not working properly.

Peugeot changed from the old carbon-encased transponder chips and introduced a new type of chip that incorporates electronic components that are placed on a circuit board. This new technology works great when it's new, however, over time, the circuit boards begin to degrade and stop working properly.

This could stop the immobiliser from working, so your vehicle won't be able to start. Contact an Peugeot specialist, or a locksmith if this is the case.

Another issue that is common is when the key fob battery gets depleted, which causes the blade of the key to stop feeding into the lock. A locksmith from your vehicle can replace the battery and cut a fresh blade for you, it's normally a quick fix.

Faulty Receiver Module

It could be that the receiver module is faulty in the event that your Peugeot key fob isn't working after being dropped on the floor, exposed to a sudden downpour or accidentally washed. The receiver module is responsible for transmitting radio frequency to the onboard computer that controls the central locking system of your Peugeot vehicle.

The key fob itself has rubber seals that prevent water from reaching the chip inside. The chip can be damaged by water when it is exposed to water for a prolonged period of time. Submerging the key fob into sea water at the beach or throwing it into the pool can be particularly damaging due to the high salt content.

The module needs to be replaced if your Peugeot spare key is no longer working. This should be done by an Peugeot specialist or an expert auto locksmith. As opposed to other cars, peugeot 107 key keys are protected by an immobilizer that is unique and requires the right coding for the start of the engine. This is why you should only choose a reputable Peugeot locksmith for the job of designing and programming the replacement.

Computer malfunctioning on-board

The on-board computer in your Peugeot is responsible for many of the systems inside the car, from airbags to power windows. The computer on board will display a code when something goes wrong. The code will be stored within the system until the problem is fixed. Often, this will involve replacing the computer on board.

One of the most common reasons for the airbag light flashing is loose or corroded connectors in the airbag sensor. This can occur due to wear and tear, ageing or exposure to moisture and salt. This problem should be addressed as soon you can, as an airbag that's malfunctioning could be dangerous in case in the event of an accident.

If your Peugeot is showing a card detected as not present error, then the battery inside the key fob might be weak or dead. This could prevent the key fob from transmitting a signal that will disable your vehicle's standard immobilizer. You can test this by pressing the unlock button on the key fob, then trying to start your car. If this does not work, the key battery is in need of replacement.