Reasons Why Your Nissan Qashqai Key Fob Won't Work

The Qashqai has a distinctly SUV-like feel due to its larger dimensions. Additionally, the ride on 19-inch wheels in Ti and ST-L models may be a bit stiff at times. Its front tyres can also lose grip on rough surfaces, and its CVT may occasionally exhibit wrist-flexing torque steer.

It is usually caused by a dead coin battery which can be easily replaced in just a few minutes. Make sure the battery you replace is of the same voltage, size and specification.

Water Damage

One of the main reasons why a Nissan key fob might display the "key ID is incorrect" message is due to water damage. The key fob has rubber seals that protect the chip inside, however prolonged exposure to moisture could cause it to stop working properly. This is typically the case when you've dropped your key fob into the ocean or into a swimming pool, but it can also happen if it gets wet from soapy hands or rain.

If your key fob was exposed to water for a long period of time it is possible to clean it with isopropyl, or an electronic cleaner. It could also require to be sent to a specialist for repair or replacement.

If your key fob has to be replaced, it is a relatively simple procedure. First, ensure that you have a multipack of the correct battery (CR2032 3V). Open the back and front cases with an abrasive screwdriver. Remove the clips made of metal, then remove the battery that was in place and replace it. After reassembling the fob put the mechanical key back in its place and make sure it is working correctly. If it isn't then you'll need to take it to an Nissan dealer or professional auto locksmith to repair the chip. The chip is not usually damaged by water and therefore shouldn't be too expensive.

Dead Coin Battery

The coin battery is a second common reason for why your Nissan Qashqai remote key fob might not function. These batteries last three to five years, but may fail over time in the event that the fob has been dropped frequently. You can try replacing the battery with a fresh one but be sure it's the same size and voltage as the original. If you choose to use another battery, it may cause the key to have an untrue key ID, which will prevent it from connecting to your vehicle.

The most efficient method of replacing the battery on the Nissan Qashqai key fob is by prying open the fob with the small screwdriver with a flat-head. The screwdriver needs to be inserted into a small hole on the bottom of your key fob. Make sure to gently twist the screwdriver to split the two halves. Remove the old CR2025 battery and replace it with a brand new one, observing the position of the previous one inside the fob.

Before you put the new nissan key - just click the next article - battery into place check to ensure there is no dirt or water damage on the terminals. If there is clean the terminals using some isopropyl ethanol. Make sure that the pole cables are connected correctly. They must be connected to the negative and the positive poles of your battery.

Troubleshooting

If your Nissan Qashqai's main fob doesn't function after being exposed to clean tap or rain water, this could be a sign that there is an issue with the internal chip. Change the battery won't fix this, and you'll need to purchase an entirely new key fob. If you dropped the key fob on the ground and it stopped working instantly it's likely due to the damage to the internal chip. You can usually get the key fob to function again if you take it out and clean the chip using alcohol and paper towels before putting it back into.

A common error that you might see on the dashboard of your car is "Key ID Not Correct." The vehicle is unable recognize the key fob, and consequently, won't allow the car to start. This can happen in many different ways, including water damage, problems that are undetectable in the circuitry of the key fob or RFID interference.

The key fob will not function in the event that the batteries with 12 volts are dead or do not provide enough electrical current. This will affect the remote keyless system and central locking on your Nissan Qashqai, as well as preventing you from starting the engine with the key fob (if equipped with Intelligent Key). Check the batteries in the key fob if you are not able to lock and unlock your door manually. Try replacing the battery to reset your transmitter.

Reprogramming

If the key fob is not been submerged in salt water the key fob should be able to be restored to its original state after a simple rinse with clean water. You can also clean the electronic chip with isopropyl or electronic cleaner. If these don't work, it may be time to replace the entire key fob with a new one.

If your Nissan Intelligent Key still does not function, there could be a connection problem between it and your vehicle. To reconnect it, begin by turning the key in the ignition, but not starting the car. Continue to do this until the hazard lights flash twice. Turn the vehicle off and remove the keys.

Open the fob compartment in your vehicle. It is typically located in the door jamb, on the handle of the driver's side or underneath an armrest. Locate the small button labeled "program" and press it. You will hear a chime when the process is completed.

Now that your Intelligent Key is relinked to the car is the time to test it out. Press all the buttons on the key while at a distance from the vehicle. If the lights flash, or the horn sounds, then the key is connected to the Nissan. You can also test it near the Nissan.