Bentley Continental Key Fob Troubleshooting Tips

The Bentley Continental is a truly amazing car to drive. Its brushed metal accents the center stack. Beautiful leather and wood wrap its interior. Its powerful W12 engine produces a whopping 552 break horsepower.

The Continental key fob is fitted with rubber seals to prevent water from damaging the electronic chip. If it is submerged clean water from the tap or rain it should be fine, but prolonged exposure to salty water can damage it.

Keyless entry system

The Bentley Continental comes with a keyless entry system, which allows you to lock and unlock your car with the remote control. This is convenient and allows you to save time and effort. However, there are several reasons why your key fob may cease to function. One of them is the battery being dead, water damage, receiver module issues and signal interference. In some cases the internal chip may be malfunctioning and could be the reason behind the problem.

The key fob is fitted with rubber seals to prevent water from reaching the electronic chips inside. The key fob can get wet if exposed salty or soapy water. This could damage your chip. It is important to clean the key fob and let it dry completely prior to replacing the battery. If the keyfob won't function after cleaning and drying, it's most likely defective and needs to be replaced.

The battery of your Continental key fob features metal retaining clips that hold it in place and complete the circuit. If the clips are damaged or corroded, it can cause contact problems. This can be fixed by looking at the battery's contacts and ensuring they're clean. You should also make sure the battery is firmly installed. If you have a spare Continental key, test it to see whether it works. If the key is faulty you can reprogram it with an OBDII scan.

Battery

The key fob has one small battery that is the size of a coin. If it's dead the remote does not work. This is simple to identify and is fixable within a couple of minutes. Water can also damage the battery, which will require the replacement. There are a variety of reasons why the key fob might not be functioning properly, including damaged buttons, defective battery contacts, signal interference, or the receiver module is dead. It is possible to reset the system by disconnecting the 12 battery for a few seconds. This will allow the system to reset itself. Connect the positive cable first, then disconnect the negative.

The battery inside the Bentley Continental key fob will last for a minimum of four years depending on the frequency you use it. The battery is held in place by metal clips. The clips should be tight however if they're not then the remote will not perform as it should.

If the Continental key fob is exposed to clean tap water, it must be cleaned with paper towel and dried before putting back the battery. If the chip is exposed to salty or soapy water, it might be fried. In these cases you'll have to buy a new key fob.

Water damage

David believes there are any major mechanical problems on this Continental. There is a little surface rust where the wheels were exposed to road grit. The boot is spacious and practical, with a factory warning triangular strapped to the floor, and a room-saving spare wheel, as well as the basic Bentley Toolkit on the false floor.

The chip on the key fob is protected by rubber seals which will ensure that it functions even if it's wet. However, prolonged exposure to water can damage the chip, and it's best to remove your key fob of your pocket when you go swimming, kayaking or rafting, canyoning or other activities where it might get wet.

If your key fob is submerged in soapy water from the washing machine or submerged in ocean water at the beach, it may be worthwhile to keep it from being damaged by cleaning the chip using isopropyl ethanol or electronic cleaner. If the key fob is unable to work after re-cleaning and drying, it may be time for a replacement. If you're looking for a Bentley Continental Key Fob, be sure that it's waterproof and factory-paired to your car.

Fault diagnosis

The Bentley Continental key fob lets you to lock and unlock your vehicle by pressing. This is a convenient system that ensures security and safety while driving. However there are some things that could cause problems with your key fob. Some of the most common reasons are a dead battery signal interference, water damage or a malfunctioning internal chip. If the key fob isn't working there are a few troubleshooting actions you can try to determine the problem.

The first thing you need to look at is the battery. Make sure it's securely inserted and that the clips for retaining it in metal are in the correct position. If the clips are not tight the battery will not get a good connection and may not work effectively. Furthermore, the retaining clips should be clean and free of corrosion.

Another reason that can cause the key fob not working is a weak car battery. The 12 volt battery in your Continental must be in good condition to be able to communicate with the remote keyless entry system and the other electronic components onboard. It is recommended to check the fuses and recharge the car battery when needed.

The bentley valet key Continental key fob sends a signal to the receiver module which is inside the ignition barrel. If the signal is lost and the engine does not start and the alarm will go off. If the Bentley continental key fob is still not working, seek help from a professional to resolve the problem.