Peugeot 208 Key Replacement

Peugeot 208 key replacement is best left to professional auto locksmiths who have the right tools and know-how. They will be able to create and program new keys quicker than a dealership and at a cheaper cost.

If your key fob has stopped locking or unlocking your doors, it is likely due to a dead coin battery. There are other causes that the key might be malfunctioning.

Dead Coin Battery

A dead coin battery will stop your Peugeot 208 from locking and unlocking, as well as preventing it from starting the engine. In this case you'll need to employ the alternate method of starting that is described in the owner's manual.

The spark plugs can also be worn out. The spark plugs light the fuel to start the engine. However they are limited in their lifespan. They will eventually break down if they aren't used frequently enough.

Luckily, there is an easy solution for this problem. Examine the voltage of your battery with a multimeter. If it's less than 11.5 Volts then you must replace it. It is also important to clean the battery's contacts when it has corrosion. You can do this by lifting the rubber covers covering the two terminals on the battery and using wire brushes to clean any corroded parts of the battery. After that, you need to connect the positive and negative pole cables.

Water Damage

If your 208 doesn't start and the battery is not running, then make sure that the spark plugs are working. It could be that they are filthy and don't spark. The spark plugs can be cleaned in a workshop.

Peugeot automobiles are equipped with a transponder that is compatible with the immobiliser. This guarantees that only the right key can turn the engine. If the chip inside the Peugeot key is damaged then it will not send the proper signal to the vehicle.

This is a typical issue that is often caused by water damage. This is particularly common in colder climates, as the vehicle might have been exposed to rain or snow. In this case, you need to contact a reliable locksmith who has the tools and equipment required to modify the key. They will also have the latest technological know-how and machinery required to make a Peugeot 208 smart key. The process should take no more than 15 minutes.

Contacts for the battery that are defective

Peugeot replaced the old transponder chips using a new version that makes use of electronic components mounted on a circuitboard. The new system works great in its initial state, but the circuit boards begin to degrade with time and cease to function properly.

This can stop the immobiliser chip from working and causing your car to not start. Contact an Peugeot specialist or a locksmith, if this is the case.

A common problem is when the battery in the key fob starts to fail. This causes the blade of the key to stop feeding into your lock. A locksmith in your car will replace the battery, and then cut a new key blade for you. This is a simple fix.

Faulty Receiver Module

If your Peugeot key fob isn't working after dropping it on the floor, being exposed to a sudden rain or accidently washing it may be due to a defective receiver module. The receiver module is responsible for transmitting radio frequencies to the onboard computer which regulates the central locking system of your Peugeot vehicle.

Rubber seals on the key fob prevent water from reaching the electronic chip. However, prolonged exposure to water could break through these seals, causing damage to the chip. The high salt content of the pool or ocean waters can cause damage to the key fob when it is submerged.

The module will have to be replaced if the Peugeot spare key is no longer working. This can only be done by an Peugeot specialist or an expert auto locksmith. Peugeot keys like other cars are protected by an immobilizer system. This requires the proper code to begin the car. This is why you must choose a reputable Peugeot locksmith for the job of programming and creating an appropriate replacement.

Faulty on-Board computer

The on-board computer inside your peugeot 206 key replacement is the one responsible for all of the systems within your car, from airbags to power windows. If something goes wrong with these systems, it'll typically display a code that identifies the problem. This code will be stored in the system until the issue is fixed. This can often mean that the on-board computers to be replaced.

One of the most common causes of the airbag light flashing is loose or corroded connection in the airbag sensor. It can be due to wear and tear, aging, or exposure to salt and moisture. This issue needs to be addressed as soon you can, since an airbag malfunctioning could be dangerous in the event of an accident.

If you notice an error message stating that the card is not found on your Peugeot, the key battery inside the key fob could be weak or dead. This could prevent the key fob from sending a signal that disables the standard immobilizer in your vehicle. You can test this by pressing the unlock button on the key fob, then trying to start your car. If this doesn't work then the battery on the key needs to be replaced.