Bentley Continental Key Fob Troubleshooting Tips

The Bentley Continental is an incredibly impressive vehicle to drive. The brushed metal exterior adorns the center stack and gorgeous leather and wood decorate its cabin. Its powerful W12 engine is able to produce 552 break horsepower.

The Continental key fob is encased by rubber to prevent water from destroying its electronic chip. If it gets submerged in clean water from the tap or rain it should be fine however prolonged exposure to salty water may cause damage to the chip.

Keyless entry system

The Bentley Continental comes with a keyless entry system that allows you to lock and unlock your vehicle using the remote control. This is convenient and helps you save time and effort. However, there are many reasons why your key fob may stop working. One of them is an empty coin battery, water damage, receiver module issues, or signal interference. In certain cases the internal chip may be malfunctioning and could be the reason behind the issue.

The key fob is fitted with rubber seals that prevent the water from getting to the electronic chips inside. The key fob can get wet when exposed to salty or soapy water. This could damage the chip. It is crucial to clean the key fob thoroughly and allow it to dry completely before placing the battery back. If the keyfob won't function after cleaning and drying, it's likely to be defective and needs to be replaced.

The metal clips on the battery of your Continental keyfob hold it in place and complete the circuit. If the clips are loosened or corroded they can cause contact problems. This can be fixed by checking the battery contacts and ensuring that they are clean. Also, make sure that the battery is properly installed. Test an extra Continental Key to see whether it works. If the key is faulty you can reprogram it by using an OBDII scan.

Battery

The key fob is equipped with an internal battery that is small in size. If it's dead the remote stops working. It is easy to identify and replace it in only a few minutes. Water can also cause damage to the battery, and this requires a replacement bentley key. There are a variety of reasons why the key fob may not be functioning properly, including worn buttons, faulty battery contacts, signal interference, or the receiver module is dead. It is possible to reset the system by disconnection of the battery at 12 volts for a few minutes. This will allow the system itself to reset itself. Remove the negative cable first and then connect the positive.

The battery of the bentley key fob replacement (Suggested Resource site) Continental key fob can last up to four years, depending on how frequently you use it. The battery is secured by metal clips. The clips should be tight however if not the remote won't function properly.

If the Continental key fob is exposed to clean tap water, it should be cleaned using a paper towel and left to dry before putting back the battery. If the chip is exposed to soapy or salty water, it may be fried. In these cases, a new keyfob will be required.

Water damage

David does not believe there are any major mechanical issues on this Continental model, aside from a little rust to the wheel trims and some surfaces that have been exposed to road grit. The boot is roomy and practical with the factory warning triangle securing to the floor, as well as a space-saver spare wheel and the basic Bentley tools under the false floor.

The chip inside the key fob is protected by rubber seals, which should keep it functioning even when it is wet. The chip can be damaged due to prolonged exposure to water. It is best to remove the key fob from your pocket prior to going for a swim, kayaking or rafting.

If the key fob you have purchased has been soaked in soapy water from the washing machine or submerged in ocean water at the beach, it may still be worth trying to save it by cleaning the chip with isopropyl alcohol or an electronic cleaner. If the key fob doesn't seem to function after re-cleaning it and drying, it could be time for a replacement. If you're in the market for a Bentley Continental key fob, be sure to select one that's waterproof and factory-paired with your car.

Fault diagnosis

The Bentley Continental keyfob enables you to lock or unlock your car in one click. This is a very convenient system and offers security and safety when driving. However, there are some things that could cause problems with your key fob. Some of the most common causes are a dead battery water damage, or signal interference. There are several troubleshooting procedures that you can apply to determine the cause of an electronic key fob not working.

The first thing to inspect is the battery. Make sure that the battery is correctly inserted and that all metal clips are in the right position. If the clips are not tight the battery will not be able to connect properly and could not function correctly. The clips used to hold them must be free of corrosion and clean.

Another reason that can cause the key fob not working is the weak battery in your car. The 12 volt battery in your Continental should be in good health to be able to communicate with the remote keyless entry system and the rest of the onboard electronics. Check the fuses and if needed, recharge your battery.

The Bentley Continental keyfob sends a message to the receiver module, which is located in the ignition barrel. If the signal isn't received, the engine won't start and an alarm will sound. If the Bentley Continental key fob still isn't working, then you should consult an expert.