Replace Nissan Key Fob Batteries

If your nissan key fob (click here to visit Littleyaksa Yodev for free) isn't responding your commands, it's a sign that its battery is dying. It's a relatively easy repair that most people are able to do themselves.

You can find an alternative from a hardware store or the owner's manual for the particular model you own and then follow these steps for changing the battery.

Change the battery

The key fob on your Nissan model comes with a built-in lithium battery which will eventually lose charge. The battery for the key fob can be changed in a matter of minutes. First, you'll need a CR2032 battery. It's a tiny coin cell battery that's often found in key fobs and is available at most convenience stores. To open the key fob, you will also need an appropriate pair (latex or not) of gloves, as well as an incredibly small screwdriver. Check the owner's manual for more detailed instructions and steps before you begin.

Flip the fob upside-down and look over the backside. There is a tiny catch that must be released by pulling it downwards. This will release the mechanical key from its original position within the fob.

Then, you can insert the new battery and make sure that it is in the correct orientation. Once the battery is placed close the fob and click the two sides together. Test your key fob after you have completed this step by pressing the unlock button. It's now possible to use the many functions of your Nissan when everything is functioning properly. After changing the battery it's recommended to re-program your key fob to ensure that it's working properly.

Replacing the Transmitter

Your key fob serves as the "key" to a myriad of your car's most crucial functions, it can be a huge loss if you misplace or damage it. A damaged or dead key fob will prevent you from locking and starting your car.

It's a great idea to have an extra key fob in your possession in case of emergency. Luckily, the process of replacing your Nissan key fob is easy. The procedure for replacing the Nissan key fob can be quite simple. You will need a new flathead screwdriver, as well as a new battery to remove the old.

You'll also require a Panasonic CR2032 3V round battery (you can find them in multipacks priced less than $5 USD). The battery will be located inside the key fob's back half and you'll have to gently pull the two halves apart to expose it. Make use of a flathead screwdriver or smaller flatheads to unbolt the clip on the top of the battery. Be sure to note its location. Replace the battery, and then put it back together to form the key fob. Test it to ensure it works.

Like any electronic device like yours, your Nissan Intelligent Key will eventually wear out due to regular usage and require to be replaced. Secure your key fob from water, magnetic fields and physical impacts. Don't drop it or put too much pressure on the device.

Replace the Key

When your Nissan key fob has gone out and you're unable to use it to unlock or start your vehicle. That's a problem for people who have to travel to work in Detroit, run errands near Dearborn or spend an evening out near Troy.

It's not too difficult to replace the battery in your Nissan Smart Key. You can do it at home or at a dealership, and you'll usually find a set for $5 or less at an hardware store.

Flip the fob over and push the small catch to the back. This will open the emergency mechanical key that is inside. While you won't be able to use the emergency key to start your vehicle, it will let you open the door.

Look for a small opening on the top of the casing. These are the perfect place to insert an screwdriver through the hole, allowing you to pull the two pieces of the key fob. Once you've gained access to the battery inside, take it out and take note of the position it is in. When you are ready to reassemble your key fobs, insert the new battery and snap the two parts of the case back together. Insert the mechanical key and your Nissan smartkey will work like a normal key.

Other Problems

Many modern vehicles come with key fobs, which let you to lock them and start them without the need for a physical key. To do this the key fob utilizes small transmitters to communicate with the car's computer system.

There are several possible reasons that your Nissan key fob will not work after you replace the battery. One possibility is that the new battery was not correctly fitted into the key fob. A reset of the key fob is a different possibility. This is a simple process that you can complete at home using just a few tools.

You'll need, for example an electric screwdriver with an angled tip to remove the old battery from the key fob. Then, you'll need a screwdriver to open the back of the key fob and insert the new battery. You'll also need to reprogramme your key fob in order for it to work with your vehicle.

Fortunately, most Nissan key fobs can be programmed by a user and you can do it yourself. It is usually done by inserting the key fob in the ignition twice within five minutes. If this does not work it is possible to take the key fob to a dealer or auto locksmith to get it programmed. The cost of this will depend on the person you call and the type of vehicle you own.