How to Replace a Kia Sportage Replacement Key

For many Kia models, the key contains a built-in keyless entry system. The key functions like a remote control and can be exchanged by an Kia dealer.

Key fobs can fail to function due to a variety of reasons, such as an inactive battery, worn out buttons signal interference, or water damage. Here are some guidelines on how to get your Kia Sportage replacement key back to working.

How to replace the remote key or smart key?

It doesn't matter if your Kia is equipped with an intelligent key, remote key push-to-start keys, or regular metal non-transponder key the battery in these keys will eventually need replacing. This is especially true if the car displays a message indicating that the smart or remote key has a low battery.

Fortunately, it's an easy procedure. To replace the battery in the key fob, remove the mechanical key from the hole in the back of the key fob and break the cover. A small screw is located inside the key fob that holds the battery in its place. Utilizing a small screwdriver take the screw off and pull out the battery that was in place. Then, insert the new and close the slit on the key fob.

When the key fob is equipped with a fresh battery check it by pressing the lock and unlock buttons. If the doors unlock and lock according to your expectations, then you're all set! You can now utilize the hands-free feature to lock and unlock your Kia when your fingers get cold or when you need to run errands around Brandon.

Note: Certain key fobs (transponder chip or smart keys) might require their programming done. This requires a special programming machine that only the dealer or automotive locksmith has access to. Other keys (non transponder keys made of steel), do not need programming. If you need to reprogramme your key, it is necessary to note the key code number on the key code tag.

How do I replace the battery?

If the Kia key fob does not respond to pressing the lock/unlock button, it's likely that the battery is depleted. A low battery can also cause other issues, such as the check engine light turning on or the engine not working properly. Fortunately, replacing the key fob battery is a simple DIY project that requires only some basic tools.

Before you begin before beginning the process, ensure that your vehicle is off and all doors are closed. Find the small metal or plastic piece on the bottom of the key fob. Press it until the metal key is released. The key can be put into the driver door handle to unlock your car.

To replace the battery inside the key fob remove the rear cover. Use a plastic pry tool to loosen up the latch that holds the black negative cable. Remove the old battery and then align the replacement battery in a way that its "+" side faces you and the "-" negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into position and avoid excessive force to avoid bending or damaging the metal contacts.

After the new battery has been installed then turn the key fob off and then turn it on in the ignition until the door locks cycle. You can then test your Kia key fob to see whether it's working again.

How to replace a smart key

Depending on the model of your kia replacement key Sportage, you may have an ordinary key fob or a smart key. The smart key comes with an embedded mechanical key blade while the standard keyfob does not. Both key fobs contain batteries that eventually need to be changed. It's an easy process that takes only two minutes.

Be sure to switch off your Kia and stand on a level well-lit and well-lit area before you begin. Remember that the fob has small pieces that could be thrown off should you not be careful.

The first step is to find the small release button that is located on the backside of the fob. This will either be a circular silver button or a rectangular slot. After pressing this button, the mechanical key blade will pop out and you can then open the key fob.

After the key fob has been open, remove the battery that was in it. The new battery is one called CR-2032 and can be purchased through the internet or at a local auto parts shop. Once you're done, your key fob should permit you to lock and unlock your vehicle, even if it isn't running.

How do I replace a mechanical key

The Kia key fob is a fantastic convenience that allows us to lock and unlock our car with the press of an button. But like any device it may have issues occasionally. There are solutions to resolve these issues and keep your key fobs functioning for many years.

One of the most frequent problems is a low or dead battery. This can cause your device to stop working or operate intermittently. If this is the case, replace the battery with an entirely new battery.

If this does not resolve the issue, try using the flathead screwdriver that is standard to push the fob's casing made of plastic open. Be careful not to damage internal components or scratch the plastic. Once the battery is opened, carefully remove the battery that was removed and replace it with a brand new one.

Close and open the door using the mechanical key. (Every Kia fob comes with a spare mechanical key that fits into the slot). Test the key fob to ensure it's working properly. If the device isn't working, contact a locksmith or dealer to resolve the issue. To avoid lockouts in the future, ensure that you have an emergency key that will be able to work with all trunk and door cylinders.