How to Replace a Kia Sportage Replacement Key

The key of many kia car key replacement models has an entry system that is keyless into. This key is similar to an remote control and can be exchanged with a Kia dealer.

Key fobs can stop working due to a number of reasons, including batteries that are dead, worn-out buttons, signal interference or water damage. Here are some guidelines on how to get your Kia Sportage replacement key working again.

How to replace a smartkey or remote key?

The battery inside your Kia's smart key will eventually have to be replaced, regardless of whether it's a remote key as well as a push-to start key or a normal metal key that doesn't contain an electronic transponder. This is especially true if the car displays a message indicating that the remote or smart key is not powered by the battery.

It's a fairly simple process. To replace the battery on the key fob, remove the mechanical key from the slit in the back of the key fob. Next, pry open the cover. A small screw will be in the key fob that holds the battery in place. With a small screwdriver, take the screw off and remove the old battery. Insert the new battery and close the opening on the key fob.

Once the key fob has new batteries check it by pressing the lock and unlock buttons. If the doors lock and unlock in the same way, you're good to go! You can now use Kia's hands-free lock/unlock function when your fingers start to get cold or you need to go on errands around Brandon.

Note: Certain key fobs (transponder chip or smart keys) may require their programming done. This requires a programming machine, which is only available to the locksmith who works for the automotive dealer. Other keys (non-transponder metal keys) don't require programming. If you need to reprogramme your key, you'll have to note the key code's number on the tag for the key code.

How do I replace a battery

If the Kia key fob is unable to respond to pressing the lock/unlock button, it is likely that the battery is not fully charged. A low battery could cause other issues such as the check engine light turning on or the engine not cranking. Fortunately replacing the key fob battery is a relatively easy DIY project that requires just a few tools.

Be sure to turn off your vehicle and close the doors before you begin. Find the small, metal or plastic piece at the bottom of your key fob, and move it until a metal key slips out. The key can be placed inside the driver door handle to unlock your car.

To replace the key fob's battery, take off the cover at the rear and use a pry bar tool to release the latch that holds the black negative battery cable. Take the old battery out, and then place the new battery to ensure that its "+" side faces you and the "-" negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into position with care to avoid using too much force to avoid bending or damaging the contacts made of metal.

After you have installed the new battery after which you turn the key fob on and off in the ignition until the door locks up. You can then test your Kia's key fob to ensure it's functioning properly.

How do you replace a smart keys

You can have an ordinary keyfob or Smart Key based upon the model of Kia Sportage. The difference between them is that the smart key is equipped with the small blade of a key tucked inside it, while the standard fob isn't equipped with. Both key fobs contain batteries that will eventually need to be changed. It's a fairly simple process that will take about two minutes.

Before you begin it is essential to make sure that you are on a level surface with good lighting and that your Kia is off. Also, remember that there are small parts inside the fob that can be snagged if not careful.

The first step is to find the small release button on the backside of the fob. It will be either a circular silver button or a rectangular slot. When you press it button, the mechanical blade will be released and you can then open the key fob.

After the key fob has been opened, take out the battery. The new battery is a CR-2032 that can be purchased online or at your local auto parts store. After you've finished, your key fob will allow you to lock the vehicle, unlock it, and then start your vehicle, even if it isn't running.

How to replace the mechanical key?

The Kia key fob is a great convenience that allows us to lock and unlock our vehicle with the push of one button. Like all devices, the Kia key fob might have issues. There are methods to fix these issues and ensure that our key fobs are in good working condition for the long term.

One of the most frequently encountered problems is a low or dead battery. This could cause the fob to stop working entirely or stop working at times. If this is the problem, replace the battery with an entirely new battery.

If this doesn't solve the problem, try using a standard flat-head screwdriver to break open the fob's plastic casing. Be careful not to damage any internal components or scratch the plastic. After the battery has been removed then replace it with a new one.

Close and open the door using the mechanical key. (Every Kia fob comes with a spare mechanical key that fits into the slot). Test the key fob to make sure it is working properly. Contact a dealer or a locksmith to fix the issue when the fob still is not working. To avoid locking outs in the future, make sure you get an emergency key that will work on all trunk and door cylinders.