Reasons Why Your Nissan Qashqai Key Fob Won't Work

The Qashqai has a distinct SUV feel to it thanks to its bigger dimensions, and the wheel sizes of 19 inches in Ti and ST-L models can be a bit stiff at times. The front tyres of Qashqai may also lose grip on rough surfaces, and the CVT could occasionally show wrist-flexing torque steering.

It is usually due to a dead battery that can be replaced in a matter of minutes. Make sure that the new battery is the same voltage, size and specifications.

Water Damage

Water damage is among the most common reasons for a Nissan keyfob to display the "key ID is incorrect" message. The key fob is fitted with rubber seals that protect the chip inside, but prolonged exposure to moisture can cause it not to function properly. It is common to observe this if your keyfob was dropped into the water or a swimming pool. However, it could also occur when it becomes wet due to the rain or soapy hands.

If your key fob is exposed to water for an extended period of time, it could need to be cleaned using isopropyl alcohol or an electronic cleaner. It could also require to be sent to a specialist to be repaired or replaced.

If your key fob does need to be replaced the process is easy. Make sure you have the right multipack (CR2032, 3V). Unlock the front and rear cases with a flathead screwdriver. You'll have to remove the clips that hold the metal together and then push out the old battery, and then insert the new one. After reassembling the fob put the mechanical key back in place and verify that it operates correctly. If it isn't then you'll have to take it to a Nissan dealer or professional auto locksmith for replacement key for nissan micra of the chip in the key. The chip is usually not damaged by water, so it should not be too expensive.

Dead Coin Battery

The coin battery is a second common reason why your Nissan Qashqai remote key fob might not work. These batteries last for three to five years, but are prone to failure over time when the fob is frequently dropped. You can try replacing the battery with a new one, but make sure that it's the same voltage and size as the original. If you replace the battery, it may cause the key to be assigned a wrong key ID. This can prevent it from being paired with your vehicle.

The best way to replace the battery of a coin on a Nissan Qashqai key fob is by prying open the key fob using a small flat head screwdriver. The screwdriver must be inserted into a small notch at the bottom of your key fob. The screwdriver should be gently twisted to separate the two halves. Remove the old CR2025 battery and replace it with a new one, observing the position of the old battery in the fob.

Before putting the new battery in be sure that there is no dirt or water damage on the terminals. If this is the case clean the terminals using the smallest amount of isopropylethanol. Make sure that the pole cables are properly connected. They should be connected to the negative and the positive poles of your battery.

Troubleshooting

If your Nissan Qashqai key fob stops working after exposure to clean rain or tap water it could be a sign of an internal chip problem. You'll need a new keyfob if you can't solve the issue by replacing the battery. If you dropped the key fob on the ground and it stopped functioning immediately, this is most likely because it damaged the internal chip. You can usually get the key fob back to function again if you take it out and clean the chip using paper towel and isopropyl alcohol and then put it back in.

A common error that you may notice on your dashboard is "Key ID Incorrect." This means that the vehicle cannot recognize the key fob, and will not allow it to start the engine. This problem could be caused in numerous ways, including water damage, malfunctions that are not detectable in the key fob circuitry or RFID interference.

If the battery that powers 12 volts in your key fob broken or is not supplying enough electrical current, it will stop working. This will affect the remote keyless system and central locking of your Nissan Qashqai, as well as hindering you from starting your engine using the key fob (if equipped with Intelligent Key). Check the battery in the key fob if it is not able to lock and unlock your door by hand. You could also try re-inserting the battery to reset the transmitter.

Reprogramming

If the key fob is not been submerged in salt water the key fob should be able to be revived after a quick rinse with clean water. You can also clean the electronic chip using isopropyl or electronic cleaner. If these don't work It could be the time to replace the entire key fob with an entirely new one.

If your Nissan Intelligent Key is still not functioning, there may be a problem with the connection between it and the car. Start by turning the ignition key but not starting the vehicle. Continue to do this until the hazard light flashes two times. Then, turn the car off and take out the keys.

Then, open the fob compartment of your vehicle. This is usually located in a door jamb, on the handle of the driver's side or under an armrest. Find the small "program" button and press it. You will hear a sound once the process is complete.

It's time to put your Intelligent Key to the test. Stand some distance away from the car, and press all the buttons on it. If the lights flash or the horn sounds, the key is connected to the Nissan. You can also test it near the Nissan.