Peugeot 208 Key Replacement

Peugeot 208 key replacement should be left to experienced auto locksmiths who have the right equipment and technical know-how. They can create and program new keys quicker than a dealership and at a lesser cost.

If the key fob stopped locking or unlocking your doors, it could be due to a dead battery in the coin. There are other reasons why the key might be malfunctioning.

Dead Coin Battery

A dead battery in the coin compartment will prevent your Peugeot 208 from locking or unlocking and won't start the engine. If this is the case, you'll have to apply the backup starting technique that's described in the owner's manual of your vehicle.

The spark plugs can also be worn out. The spark plugs are responsible for igniting the fuel that ignites the engine. They only last for a certain amount of time. They'll eventually break down in the event that they aren't utilized enough.

Luckily, there is an easy solution for this issue. Check the voltage of the battery using a multimeter. If it's lower than 11.5 Volts, then you need to replace it. If the battery has corroded, it is important to clean its contacts. This can be done by lifting the rubber covers that protect the two battery terminals and using a wire brush to remove any parts that are corroded from the battery. Then, you should reconnect the positive pole cables to the negative.

Water Damage

If your 208 doesn't start and the battery is not flat, then you need to make sure that the spark plugs are functioning. It could be that they're dirty and they don't spark. The spark plugs can be cleaned in an workshop.

Peugeot cars are equipped with a transponder key that integrates with the car's immobiliser system. This ensures that only the right key can turn the engine. If the chip in the Peugeot key is damaged then it will not transmit the proper signal to the vehicle.

Water damage is a typical cause of this issue. This is especially prevalent in colder climates, as the vehicle might have been exposed to snow or rain. In this case, you need to contact a reputable locksmith who has the tools and equipment needed to reprogram the key. They will also have the latest technology and machinery required to make the Peugeot smart key. The process shouldn't last more than 15 minutes.

Contacts for the battery that are defective

Peugeot replaced the old transponder chips with a new model that utilizes electronic components that are mounted on a circuit board. This new system works great when it's brand new but as time passes, the circuit boards begin to wear out and stop functioning properly.

This could stop the immobiliser chip from working and causing your car to not start. If this is the case, it's best to seek out a Peugeot specialist or locksmith.

The most frequent issue is when the battery inside the key fob begins to fail. This causes the blade of the key to stop feeding into the lock. A locksmith for cars can replace the battery and cut a new blade for you, it's normally a quick fix.

Faulty Receiver Module

It could be that the receiver module is faulty If your Peugeot key fob stops working after being dropped on the floor, or exposed to a sudden downpour or accidentally washed. The receiver module is responsible for transmitting radio frequency to the onboard computer which manages the central locking system of your Peugeot vehicle.

The key fob itself has rubber seals to prevent water from getting to the electronic chip inside. Water can damage the chip in the event that it is exposed water for a prolonged period of period of. Submerging the key fob in ocean water at the beach or throwing it into the pool could be especially damaging because of the high salt content.

The module needs to be replaced if the Peugeot spare key no longer works. This should be done by an Peugeot specialist or expert auto locksmith. Peugeot keys like other cars are protected by an immobilizer system. This requires the proper code to begin the car. This is the reason why you should only go with a knowledgeable Peugeot locksmith to handle the task of creating and programming the replacement.

Computers with faulty on-board computers

The on-board computer inside your Peugeot is responsible for many of the systems within your vehicle, from power windows to the airbags. If something is wrong with these systems, it will typically display a code indicating the issue. The code is stored within the system until the problem is resolved. This may require the on-board computers to be replaced.

One of the main causes of the airbag light turning on is the loose or corroded connectors in the airbag sensor. This can occur due to wear and tear, aging or exposure to salt and moisture. This problem should be taken care of as soon as you can, because an airbag that is malfunctioning could pose danger in the event of an accident.

If your Peugeot is showing a card detected as not present error, the battery in the key fob could be dead or weak. This can prevent the key fob from sending a signal that disarms the immobilizer on your vehicle's standard. Try this by pressing the unlock key on the key fob, and then trying to start your vehicle. If this doesn't work then the battery in the key needs to be replaced.